INITIAL JET 4-4/110/220-60
| Hydraulic data | |
|---|---|
| Maximum operating pressure PN | 7 bar |
| Discharge port | G 1 |
| Min. fluid temperature Tmin | 5 °C |
| Max. fluid temperature Tmax | 35 °C |
| Min. ambient temperature Tmin | 0 °C |
| Max. ambient temperature Tmax | 40 °C |
| Motor data | |
|---|---|
| Mains connection | 1~110-220 V, 60 Hz |
| Voltage tolerance | ±6 % |
| Shaft power P2(Q=max.) of selected impeller * number of pumps NO VALUE | 750 W |
| Rated power P2 | 0.75 kW |
| Rated current IN | 5 A |
| Rated speed n | 3600 1/min |
| Insulation class | F |
| Protection class | IPX4 |
| Materials | |
|---|---|
| Pump housing | Grey cast iron |
| Impeller | Stainless steel |
| Shaft | Steel |
| Shaft seal | BQ1PFF |
| Gasket material | NBR |
| Installation dimensions | |
|---|---|
| Pipe connection on the suction side DNs | G 1 |
| Pipe connection on the discharge side DNd | G 1 |
Wilo-INITIAL JET 4-4
| Product data | |
|---|---|
| Brand | Wilo |
| Product description | INITIAL JET 4-4/110/220-60 |
| Article number | 4262294 |
| EAN number | 4062679328638 |
| Minimum order quantity | 1 |
| Date of sales availability | 2023-06-26 |
| Packaging | |
|---|---|
| Packaging type | Cardboard box |
| Packaging property | Transport packaging |
| Pieces per pallet | 1 |
| Number per layer | 1 |
| Dimension, weight | |
|---|---|
| Length with packaging | 453 mm |
| Length L | 435 mm |
| Height with packaging | 241 mm |
| Height H | 204 mm |
| Width with packaging | 201 mm |
| Width W | 187 mm |
| Gross weight, approx. m | 16.6 kg |
| Net weight, approx. m | 16 kg |
Self-priming single-stage jet pump for water supply, irrigation and rainwater utilisation. Self-priming up to 8 m. Electrical connection via a terminal box.
Application
- Pumping water from wells
- Filling, pumping empty, transferring by pumping, irrigation and sprinkling
- As emergency pump for overflows
| Materials | |
|---|---|
| Pump housing | Grey cast iron |
| Shaft | Steel |
| Shaft seal | BQ1PFF |
| Gasket material | NBR |
| Impeller | Stainless steel |
| Operating Data | |
|---|---|
| Min. fluid temperature Tmin | 5 °C |
| Max. fluid temperature Tmax | 35 °C |
| Maximum operating pressure p | 6.0 bar |
| Discharge port | G 1 |
| Max. ambient temperature Tmax | 40 °C |
| Motor data | |
|---|---|
| Mains connection | 1~110-220 V, 60 Hz |
| Voltage tolerance | ±6 % |
| Rated power P2 | 0.75 kW |
| Rated current IN | 5 A |
| Rated speed n | 3600 1/min |
| Insulation class | F |
| Protection class | IPX4 |
| Installation dimensions | |
|---|---|
| Pipe connection on the suction side DNs | G 1 |
| Pipe connection on the discharge side DNd | G 1 |
| Ordering information | |
|---|---|
| Net weight, approx. m | 16 kg |
| Brand | Wilo |
| Product description | INITIAL JET 4-4/110/220-60 |
| Article number | 4262294 |
Installation and operating instructions
Wilo-Initial JET
| Article Number | 4168383 |
| Edition | 2023-08 |
| Number of pages | 2 |
| Language | en |
INDD (14 MB)Group Statement
Group Statement REACH
| Edition | 2021-05 |
| Number of pages | 5 |
| Language | language neutral |
PDF (279 KB)In inlet mode (2) | |||
Ball valve with lever for easy and safe installation. Certified suitability in accordance with CE for drinking water applications (e.g. in accordance with DIN 1988). Ball valves DVGW-certified up to Rp 2. Scope of delivery
| |||
Kit is comprised of 2 union nuts and 2 threaded nozzles made of brass and 2 seals. For valves with flat-sealing male thread. | |||
In suction mode (1) | |||
Ball valve with lever for easy and safe installation. Certified suitability in accordance with CE for drinking water applications (e.g. in accordance with DIN 1988). Ball valves DVGW-certified up to Rp 2. Scope of delivery
| |||
In suction mode with floating intake (8) | |||
Ball valve with lever for easy and safe installation. Certified suitability in accordance with CE for drinking water applications (e.g. in accordance with DIN 1988). Ball valves DVGW-certified up to Rp 2. Scope of delivery
| |||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 10.0 m (cpl.) | 2025976 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 15.0 m (cpl.) | 2025977 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 3.0 m (cpl.) | 2025974 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Floating coarse suction filter for water extraction close to the surface of prefiltered rain water. Connection R 1¼” via customer-provided suction-proof hose connection to the pump used. Filter type GR: Coarse suction filter with non-return valve, mesh width 1.8 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Scope of delivery
| |||
Floating fine suction filter for water extraction close to the surface with prefiltered rain water for the protection of the downstream rainwater supply system. Version with hose connection nozzle R 1¼”. Filter type FR: Fine suction filter with non-return valve, mesh width 1.2 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Only for well pre-filtered rainwater without coarse constituents. The quantity of coarse constituents has a direct influence on the frequency of filter cleaning. Check filter regularly for dirt! Scope of delivery
| |||
In suction mode with suction hose (3) | |||
Ball valve with lever for easy and safe installation. Certified suitability in accordance with CE for drinking water applications (e.g. in accordance with DIN 1988). Ball valves DVGW-certified up to Rp 2. Scope of delivery
| |||
Suction hose kit for use in the domestic water supply. Scope of delivery
| |||
Suction hose kit for use in the domestic water supply. Scope of delivery
| |||
Fittings (1) | |||
Ball valve with lever for easy and safe installation. Certified suitability in accordance with CE for drinking water applications (e.g. in accordance with DIN 1988). Ball valves DVGW-certified up to Rp 2. Scope of delivery
| |||
Hoses / hose joints (7) | |||
Suction hose kit for use in the domestic water supply. Scope of delivery
| |||
Suction hose kit for use in the domestic water supply. Scope of delivery
| |||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 3.0 m (cpl.) | 2025974 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 5.0 m (cpl.) | 2025975 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction/pressure hose 1¼" SE, PN 10, 10.0 m (cpl.) | 2025976 | ||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction-resistant and pressure-resistant hose for vacuum-tight connection of pump suction port and floating extractor. Scope of delivery
| |||
Suction filter (4) | |||
Floating coarse suction filter for water extraction close to the surface of prefiltered rain water. Connection R 1¼” via customer-provided suction-proof hose connection to the pump used. Filter type G: Coarse suction filter without non-return valve, mesh width 1.8 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Scope of delivery
| |||
Floating coarse suction filter for water extraction close to the surface of prefiltered rain water. Connection R 1¼” via customer-provided suction-proof hose connection to the pump used. Filter type GR: Coarse suction filter with non-return valve, mesh width 1.8 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Scope of delivery
| |||
Floating fine suction filter for water extraction close to the surface with prefiltered rain water for the protection of the downstream rainwater supply system. Version with hose connection nozzle R 1¼”. Filter type F: Fine suction filter without non-return valve, mesh width 1.2 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Only for well pre-filtered rainwater without coarse constituents. The quantity of coarse constituents has a direct influence on the frequency of filter cleaning. Check filter regularly for dirt! Scope of delivery
| |||
Floating fine suction filter for water extraction close to the surface with prefiltered rain water for the protection of the downstream rainwater supply system. Version with hose connection nozzle R 1¼”. Filter type FR: Fine suction filter with non-return valve, mesh width 1.2 mm Note Suitable for applications in domestic water supply for all pump types with a rated volume flow of approx. 3 m3/h. Only for well pre-filtered rainwater without coarse constituents. The quantity of coarse constituents has a direct influence on the frequency of filter cleaning. Check filter regularly for dirt! Scope of delivery
| |||
Valves/accessories (1) | |||
Kit is comprised of 2 union nuts and 2 threaded nozzles made of brass and 2 seals. For valves with flat-sealing male thread. | |||
Wall fixation/installation on a base (1) | |||
Wall bracket incl. installation accessories for secure fixation of the Wilo-HiControl and Wilo-HiControl EK pressure and flow controllers, as well as Wilo-Fluidcontrol and Wilo-Fluidcontrol EK. Scope of delivery Fixation set comprising
| |||
Pump control (2) | |||
Electronic control and regulation accessories. The Wilo-HiControl 1 series is used for borehole pumps to enable automatic operation. Wilo-HiControl 1 protects the pump against operation with a low volume flow. The volume flow sensor and pressure sensor enable Wilo-HiControl 1 to automate the pump between two values: the start-up pressure and the switch-off volume flow. If the pressure in the network is lower than the start-up pressure, Wilo-HiControl 1 starts the pump. The pump continues to operate until the volume flow falls below the value of the switch-off volume flow. The small internal tank prevents water hammer and cycling. The Wilo-HiControl 1-EK version with electrical cable and built-in socket shortens the installation time as the pump can be directly connected to the power supply. Wilo-HiControl 1 can be mounted on surface pumps or connected to submersible pumps for domestic water supply. Special features
Inline version with input and output in vertical axis and uniform thread connections, suitable for direct connection to the pump housing or wall surface installation with a wall bracket (accessories). Notice The HiControl 1 may be installed only in vertical position with the output at the top! Scope of delivery
| |||
Electronic control and regulation accessories. The Wilo-HiControl 1 series is used for borehole pumps to enable automatic operation. Wilo-HiControl 1 protects the pump against operation with a low volume flow. The volume flow sensor and pressure sensor enable Wilo-HiControl 1 to automate the pump between two values: the start-up pressure and the switch-off volume flow. If the pressure in the network is lower than the start-up pressure, Wilo-HiControl 1 starts the pump. The pump continues to operate until the volume flow falls below the value of the switch-off volume flow. The small internal tank prevents water hammer and cycling. Wilo-HiControl 1 can be mounted on surface pumps or connected to submersible pumps for domestic water supply. Special features
Inline version with input and output in vertical axis and uniform thread connections, suitable for direct connection to the pump housing or wall surface installation with a wall bracket (accessories). Notice The HiControl 1 may be installed only in vertical position with the output at the top! Scope of delivery
| |||
Pump control/accessories (2) | |||
The kit detects low water using pressure measurement and is adjusted to the increase in pressure and pressure maintenance of non-potable water. The kit is used exclusively for single-phase products. For horizontal pumps, the connection is established for 1" or 1"1/4 using a reduction nipple M/M 1"1/4-1". For vertical pumps, the oval shape 1"1/4 connection is possible using an oval counter flange with an O-ring. The switch-on and switch-off pressure for needs-based operation and pressure range of the pump is configured on the reverse pressure switch. The pressure measurement is carried out using a single-phase low pressure switch. If the pressure decreases and reaches 0.1 bar, the pump is stopped. The pump starts again when the pressure rises and reaches 0.5 bar. These starting and stopping pressure values are factory settings and can be changed. You can use the pressure gauge to define the values. Scope of delivery The kit is supplied with the following, unmounted components:
| |||
The kit detects low water using pressure measurement and is adjusted to the increase in pressure and pressure maintenance of non-potable water. The kit is used exclusively for single-phase products. For horizontal pumps, the connection is established for 1"1/2 or 2" using a reduction nipple M/M 2"-1"1/2. For vertical pumps, the oval shape 2" connection is possible using an oval counter flange with an O-ring. The switch-on and switch-off pressure for needs-based operation and pressure range of the pump is configured on the reverse pressure switch. The pressure measurement is carried out using a single-phase low pressure switch. If the pressure decreases and reaches 0.1 bar, the pump is stopped. The pump starts again when the pressure rises and reaches 0.5 bar. These starting and stopping pressure values are factory settings and can be changed. You can use the pressure gauge to define the values. Scope of delivery
| |||
Pressure control (10) | |||
Kit for a pressure-constant control (p-c) of Helix EXCEL, Helix VE, MHIE, MVIE and MVISE pumps, control signal 4 – 20 mA. Scope of delivery
| |||
Pressure sensor kit, 10 BAR | 4048064 | ||
Kit for a pressure-constant control (p-c) of Helix EXCEL, Helix VE, MHIE, MVIE and MVISE pumps, control signal 4 – 20 mA. Scope of delivery
| |||
Pressure sensor kit, 16 BAR | 4048065 | ||
Kit for a pressure-constant control (p-c) of Helix EXCEL, Helix VE, MHIE, MVIE and MVISE pumps, control signal 4 – 20 mA. Scope of delivery
| |||
Kit for a pressure-constant control (p-c) of Helix EXCEL, Helix VE, MHIE, MVIE and MVISE pumps, control signal 4 – 20 mA. Scope of delivery
| |||
Signal transmitter for differential pressure-sensitive infinitely variable speed control. Note Take care to ensure that a non-return valve is placed between pump and sensor. Further maintenance valves and a diaphragm pressure vessel are required for error-free functioning. Scope of delivery
| |||
Pressure sensor, 0 - 10 bar | 2550661 | ||
Signal transmitter for differential pressure-sensitive infinitely variable speed control. Note Take care to ensure that a non-return valve is placed between pump and sensor. Further maintenance valves and a diaphragm pressure vessel are required for error-free functioning. Scope of delivery
| |||
Pressure sensor, 0 - 16 bar | 2550662 | ||
Signal transmitter for differential pressure-sensitive infinitely variable speed control. Note Take care to ensure that a non-return valve is placed between pump and sensor. Further maintenance valves and a diaphragm pressure vessel are required for error-free functioning. Scope of delivery
| |||
Pressure sensor, 0 - 25 bar | 2550663 | ||
Signal transmitter for differential pressure-sensitive infinitely variable speed control. Note Take care to ensure that a non-return valve is placed between pump and sensor. Further maintenance valves and a diaphragm pressure vessel are required for error-free functioning. Scope of delivery
| |||
Signal transmitter for differential pressure-sensitive infinitely variable speed control. Note Take care to ensure that a non-return valve is placed between pump and sensor. Further maintenance valves and a diaphragm pressure vessel are required for error-free functioning. Scope of delivery
| |||
For mounting an automatic two-pump system with pressure-dependent operation. The pressure sensor measures the applied pressure and delivers signals for switchgear with a 4 – 20 mA input. Notice Take care to ensure that a non-return valve is placed between pump and kit! Scope of delivery
| |||
Level control (24) | |||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA65 with 10 m cable | 503211893 | ||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA65 with 20 m cable | 2004431 | ||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA65 with 30 m cable | 2004432 | ||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA KR1 S with 5 m cable | 6082806 | ||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA KR1 S with 10 m cable | 6082807 | ||
As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WA65 (PSN-X) with 20 m cable | 6088843 | ||
As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC | |||
Float switch WA65 (PSN-X) with 10 m cable | 6088844 | ||
As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC | |||
As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC | |||
Small EK switchgear complete with float switch wired for ready-to-plug consumer (1~230 V, 50 Hz) to 1 kW rated power. The float switch functions as a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Float switch WAEK 65, 10 m cable | 2005516 | ||
Small EK switchgear complete with float switch wired for ready-to-plug consumer (1~230 V, 50 Hz) to 1 kW rated power. The float switch functions as a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Small EK switchgear complete with float switch wired for ready-to-plug consumer (1~230 V, 50 Hz) to 1 kW rated power. The float switch functions as a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF | |||
Small EK switchgear complete with float switch wired for ready-to-plug consumer (1~230 V, 50 Hz) to 1 kW rated power. The float switch functions as a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up OFF, down ON | |||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 4 m | 2516278 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 5 m | 500937990 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 10 m | 2501937 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 20 m | 2516283 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 25 m | 2000601 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 30 m | 2514045 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 35 m | 2516284 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 40 m | 2516285 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Submersible electrode, 50 m | 2500315 | ||
Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications. | |||
Signal transmitter without connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. Notice: The connection cable must be provided and connected by the customer! | |||