Sub TWI 6.30-26-C-SD | Wilo

Similar to figure

Sub TWI 6.30-26-C-SD

Article number: 6075249

Hydraulic data
Minimum efficiency index (MEI)	≥0.4
Maximum operating pressure PN	40 bar
Max. sand content	50 g/m³
Max. immersion depth	350 m
Max. volume flow Q_max	42.1 m³/h
Optimal volume flow Q_opt	28.9 m³/h
Max. delivery head H_max	282.7 m
Optimal delivery head H_opt	199.9 m
Min. fluid temperature T_min	3 °C
Max. fluid temperature T_max	30 °C
Number of stages	26

Motor data
Mains connection	3~400 V, 50 Hz
Rated power P₂	30 kW
Rated speed n	2860 1/min
Rated current I_N	65 A
Starting current I	132 A
Activation type	Star-Delta (YΔ)
Power factor cos φ₁₀₀	0.81
Max. switching frequency t	20 1/h
Motor diameter DM	137 mm

Cable
Connection cable length L	4 m
Cable cross-section	2x 4G4 mm²

Materials
Pump housing	Stainless steel
Impeller	Stainless steel
Shaft	Stainless steel
Motor housing	Grey cast iron

Installation dimensions
Pipe connection on the discharge side DNd	Rp 3

Product data
Brand	Wilo
Product description	Sub TWI 6.30-26-C-SD
Article number	6075249
EAN number	4048482539980
Colour	Silver
Minimum order quantity	1
Date of sales availability	2010-01-01

Packaging
Packaging type	Box
Packaging property	Transport packaging
Pieces per pallet	1
Number per layer	1

Dimension, weight
Length with packaging	4100 mm
Length L	3803 mm
Height with packaging	420 mm
Height H	149 mm
Width with packaging	300 mm
Width W	149 mm
Gross weight, approx. m	188 kg
Net weight, approx. m	133 kg

Fully submersible, multistage pump for pumping industrial and drinking water (ACS rating) with radial or semi-axial impellers in sectional construction for vertical or horizontal installation, with built-in non-return valve. Corrosion-free, three-phase AC motor for direct or star-delta starting with water-glycol filling, alternatively with drinking water filling. Hermetically cast motor with enamel-insulated winding, resin-impregnated or rewindable with PVC-insulated winding, and self-lubricating bearings. The motor is cooled by the pumped fluid. Therefore, the unit must always be operated immersed. The limit values for maximum fluid temperature and minimum flow velocity must be adhered to. Vertical installation is possible with or without cooling jacket. In cases of horizontal installation, a cooling jacket must always be provided .

Scope of delivery:

Submersible pump with connection cable and ACS rating
Installation and operating instructions

Operating Data
Max. delivery head H_max	282.7 m

Unit
Minimum efficiency index (MEI)	≥0.4
Pipe connection on the discharge side DNd	Rp 3
Maximum operating pressure p	40.0 bar
Max. sand content	50 g/m³
Protection class motor	IP68
Max. immersion depth	350 m
Min. fluid temperature T_min	3 °C
Max. fluid temperature T_max	30 °C
Net weight, approx. m	133 kg
Max. diameter D_max	149 mm

Motor data
Motor design	Submersible motor
Mains connection	3~400 V, 50 Hz
Rated power P₂	30 kW
Rated speed n	2860 1/min
Rated current I_N	65 A
Activation type	Star-Delta (YΔ)
Max. switching frequency t	20 1/h
Motor diameter DM	137 mm
Min. flow rate at the motor m/s	0.1 m/s

Cable
Connection cable length L	4 m
Cable cross-section	2x 4G4 mm²

Materials
Pump housing	Stainless steel
Motor housing	Grey cast iron
Shaft	Stainless steel
Impeller	Stainless steel

Ordering information
Net weight, approx. m	133 kg
Brand	Wilo
Product description	Sub TWI 6.30-26-C-SD
Article number	6075249

Installation and operating instructions

Wilo-Sub TWI 4-6

Article Number	4069717
Edition	2021-10
Number of pages	60
Language	bg, cs, da, el, en, et, fi, hr, hu, it, lt, lv, mk, nl, no, pl, pt, ro, sl, sr, sv, uk

PDF (3 MB)

Download

Wilo-Sub TWI 4-6

Article Number	4069717
Edition	2021-10
Number of pages	12
Language	en

PDF (984 KB)

Download

Fittings (3)
Pressure gauge
Pressure gauge	Pressure gauge 0 - 6 bar	2028687
	Pressure gauge for displaying the current pressure in the pipe network. Note Horizontal pressure connection
	Pressure gauge 0 - 40 bar	2502048
	Pressure gauge for displaying the current pressure in the pipe network. Note Horizontal pressure connection
	Pressure gauge 0 - 25 bar	2660743
	Pressure gauge for displaying the current pressure in the pipe network. Note Horizontal pressure connection
Installation/setup (1)
Cable terminal
Cable terminal	Cable terminal (stainless steel) for stainless steel cable (Ø 3 mm)	21040
Cable terminal	For fastening the Niro wire rope with 3 mm² cross-section to the support hooks of 3" and 4" pumps. Scope of delivery Cable terminal 2 bolts
Motor cooling (2)
Cooling jacket, horizontal
Cooling jacket, horizontal	Cooling jacket pipe for 6" submersible-motor pumps.	6042339
Cooling jacket, horizontal	Submersible-motor pumps can be equipped with a cooling jacket pipe to achieve the flow velocity necessary for motor cooling. Note In cases of horizontal installation, a cooling jacket must always be provided . Exception: Sprinkler pumps with VdS approval require no cooling jackets Scope of delivery Cooling jacket pipe Bearing bracket for motor Bearing bracket for hydraulics Spacer Spacing ring Screw clamps
Cooling jacket, vertical
Cooling jacket, vertical	Cooling jacket pipe for 6" submersible pumps.	6041875
Cooling jacket, vertical	Submersible-motor pumps can be equipped with a cooling jacket pipe to achieve the flow velocity necessary for motor cooling. This is recommended especially if: Sludge deposits could form on the motor (e.g., for application in a pump sump immediately above ground) Improved motor cooling is required because of unusual operating conditions No unperforated well casing is present in the well, and the pump must be installed in the filtration pipe network Sand appears in the well Installation takes place in rock springs without pipe networks Scope of delivery Cooling jacket pipe Spacer Spacing ring Screw clamps
Pressure control (6)
Pressure reducer
Pressure reducer	Pressure reducer R ½	2531892
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
	Pressure reducer R ¾	2531893
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
	Pressure reducer R 1	2531894
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
	Pressure reducer R 1¼	2531895
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
	Pressure reducer R 1½	2531896
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
	Pressure reducer R 2	2531897
	Pressure reducer for the prevention of pressure damage and for reducing water consumption. In addition, irritating flow noise is minimised due to p = const. control. Version Housing with pressure gauge connection on both sides Variably adjustable by means of a setting screw Setpoint spring Valve insert including diaphragm Fine sieve (0-16 mm) DVGW-certified
Pressurised expansion tanks (18)
Diaphragm pressure vessel DT5 junior
Diaphragm pressure vessel DT5 junior	Diaphragm expansion tank DT5 junior 60, PN 10	2515527
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 80, PN 10	2515528
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 100, PN 10	2515529
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 200, PN 10	2515530
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 300, PN 10	2515531
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 400, PN 10	2524232
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
	Diaphragm expansion tank DT5 junior 500, PN 10	2515532
	Type-tested diaphragm pressure vessels for use in conjunction with drinking water, water-supply or pressure boosting systems. The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment Throughflow, complete with throughflow fitting including shut-off and drain Diaphragm exchangeable in accordance with KTW C and W 270 starting from 60 l Built and tested in accordance with DIN 4807 T5, DIN DVGW Reg. no. NW-9481AU2123 and NW-9481AT2535 Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice Use of the diaphragm pressure vessels on the supply pressure side must comply with the specifications of the local water-supply companies.
Diaphragm pressure vessel type D
Diaphragm pressure vessel type D	Diaphragm pressure vessel type DD (12DD-PN16)	2515517
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Type D (33D-PN10) diaphragm expansion tank	2534897
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
Diaphragm pressure vessel type DE
Diaphragm pressure vessel type DE	Diaphragm pressure vessel type DE (18DE-PN11)	2502038
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (25DE-PN10)	2515518
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (33DE-PN10)	2515519
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (60DE)	2515523
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (80DE)	2515524
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (100DE)	2515525
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (200DE)	2511823
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (300DE)	2515526
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!
	Diaphragm pressure vessel type DE (500DE)	2511831
	The vessels are for the purpose of avoiding pressure surges in the system and reduce the switching frequency of the pumps/system. Equipment no throughflow, no shutoff and no draining Construction in acc. with DIN EN 13831 parts that come in contact with fluids are corrosion-free Approved and maintained in accordance with Pressure Appliances Directive 97/23/EG and further technical regulations Notice These expansion tanks are not in conformity with DIN 4807/T5 and, for that reason, not authorised for utilisation in drinking water systems in Germany!

Pump control (1)
Wilo-EFC
Wilo-EFC	EFC37 3x380-480V 50/60Hz IP55	2193444
Wilo-EFC	A stand-alone frequency converter for fixed-speed pumps that are operated in variable applications, especially for heating, air conditioning and pressure boosting. Special features/product advantages Compact design with an energy-saving cooling concept for lowering temperature losses Integrated energy-efficient harmonic reduction function in the pump’s partial load range Versatile pumping application scenarios thanks to differing connection options and different control modes Simple commissioning thanks to an intuitive assistant with graphical user interface Options External communication via IF modules (optional): Profibus, DeviceNet, Profinet, Ethernet, Modbus Scope of delivery Stand-alone frequency converter Installation and operating instructions
Pump control/accessories (1)
Pt 100 sensor
Pt 100 sensor	Pt 100 sensor for 6" motors	6028701
Pt 100 sensor	Screw-in PT100 sensor for thermal monitoring, suitable for subsequent connection to 6" and 8" motors.
Pump control/Comfort control system (4)
W-CTRL-CC-WP
W-CTRL-CC-WP	W-CTRL-CC-WP-1x72,0A-T4-SD-WM-PKG	2540292
	Wilo-Comfort Controller for connecting pumps for water supply from bore holes and tanks. Fully electronic Comfort Controller (CC) in steel sheet housing as floor model or for wall fixation, RAL 7035 (structure), protection class IP54, completely wired. Switchgear suitable for connection to three-phase networks 3/PE 400 V/50 Hz in accordance with IEC 60038 (other voltages on request). Specially adjusted for borehole pumps from the Wilo catalogue. The Comfort Controller CC consists of: Internal power supply CPU (+ backup battery) Analogue/digital modules Power section with fuses, contactors and motor-protection equipment Graphics-capable touch display with 3-colour backlight for indicating the operating status operation/fault/acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, diagram function Main switch, internal Manual-0-Automatic service selector on each pump Operating mode selection (Manual/Off/Automatic) for each pump via touch display Potential-free contacts (changeover contact) for collective run and fault signals (SBM/SSM), individual operation and individual fault signals (EBM/ESM) and dry running signal for each pump Evaluation relay (for each pump) for the connection of submersible electrodes for low-water cut-out switchgear (detachable for each pump with separated boreholes) Digital inputs for switching external systems ON/OFF, anti-frost protection alarm signal, setpoint switchover** Analogue input 0/4-20mA for external setpoint adjustment Overload protection via thermal winding contact, motor protection via motor protection switch/in star-delta start-up, starting from 5.5 kW via thermal overload relay (optional: PTC/PT100 triggering available) PID controller, automatic pump alteration and service life optimisation for multi-pump systems Three setpoints are selectable by default Automatic fault-actuated switchover to idle pump Short test run of pump(s) during standstill, pilot pump function Automatic, load-sensitive cut-in of peak-load pump depending on the programmable control variables Programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system deactivation Signal and one pump at speed adjustable on frequency converter Additional charge for optional modules (installation in factory or later after technical clarification): Temperature module For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Modbus RTU, Profibus, LON bus, CAN bus, Ethernet, others on request. Signal converter for external remote setpoint adjustment or control mode using 0/2 – 10 V signals. Evaluation relay for PTC/PT100. Buffered power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. * on-site potential-free NC contact ** on-site potential-free NO contact Order example: W-CTRL-CC-WP-2x20,0A-T4-DOL-BM-PKG Switchgear for 2 pumps with max. rated pump current of 20.0 A WP = version for borehole pump applications (well pump), contains the equipment described above T4 = mains connection 3~400 V DOL = activation type of the pump: direct BM = designed as switch cabinet floor model PKG = with packaging Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	W-CTRL-CC-WP-1x72,0A-T4-SD-FC-BM-PKG	2540310
	Wilo-Comfort Controller for connecting pumps for water supply from bore holes and tanks. Fully electronic Comfort Controller (CC) in steel sheet housing as floor model or for wall fixation, RAL 7035 (structure), protection class IP54, completely wired. Switchgear suitable for connection to three-phase networks 3/PE 400 V/50 Hz in accordance with IEC 60038 (other voltages on request). Specially adjusted for borehole pumps from the Wilo catalogue. The Comfort Controller CC consists of: Internal power supply CPU (+ backup battery) Analogue/digital modules Power section with fuses, contactors and motor-protection equipment as well as frequency converter and sine filter Graphics-capable touch display with 3-colour backlight for indicating the operating status operation/fault/acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, diagram function Main switch, internal Manual-0-Automatic service selector on each pump Operating mode selection (Manual/Off/Automatic) for each pump via touch display Potential-free contacts (changeover contact) for collective run and fault signals (SBM/SSM), individual operation and individual fault signals (EBM/ESM) and dry running signal for each pump Evaluation relay (for each pump) for the connection of submersible electrodes for low-water cut-out switchgear (detachable for each pump with separated boreholes) Digital inputs for switching external systems ON/OFF, anti-frost protection alarm signal, setpoint switchover** Analogue input 0/4-20 mA for external setpoint adjustment or control mode (only in version CC…FC and possible only with single-pump operation) Overload protection via thermal winding contact, motor protection via motor protection switch/in star-delta start-up, starting from 5.5 kW via thermal overload relay (optional: PTC/PT100 triggering available) PID controller, automatic pump alteration and service life optimisation for multi-pump systems Three setpoints are selectable by default Automatic fault-actuated switchover to idle pump Short test run of pump(s) during standstill, pilot pump function Automatic, load-sensitive cut-in of peak-load pump depending on the programmable control variables Programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system deactivation Signal and one pump at speed adjustable on frequency converter Additional charge for optional modules (installation in factory or later after technical clarification): Temperature module For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Modbus RTU, Profibus, LON bus, CAN bus, Ethernet, others on request. Signal converter for external remote setpoint adjustment or control mode using 0/2 – 10 V signals. Evaluation relay for PTC/PT100. Buffered power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. * on-site potential-free NC contact ** on-site potential-free NO contact Order example: W-CTRL-CC-WP-2x20,0A-T4-DOL-FC-BM-PKG Switchgear for 2 pumps with max. rated pump current of 20.0 A WP = version for borehole pump applications (well pump), contains the equipment described above T4 = mains connection 3~400 V DOL = activation type of the pump: direct FC = with frequency converter & sine filter BM = designed as switch cabinet floor model PKG = with packaging Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	W-CTRL-CC-WP-2x72,0A-T4-SD-FC-BM-PKG	2540311
	Wilo-Comfort Controller for connecting pumps for water supply from bore holes and tanks. Fully electronic Comfort Controller (CC) in steel sheet housing as floor model or for wall fixation, RAL 7035 (structure), protection class IP54, completely wired. Switchgear suitable for connection to three-phase networks 3/PE 400 V/50 Hz in accordance with IEC 60038 (other voltages on request). Specially adjusted for borehole pumps from the Wilo catalogue. The Comfort Controller CC consists of: Internal power supply CPU (+ backup battery) Analogue/digital modules Power section with fuses, contactors and motor-protection equipment as well as frequency converter and sine filter Graphics-capable touch display with 3-colour backlight for indicating the operating status operation/fault/acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, diagram function Main switch, internal Manual-0-Automatic service selector on each pump Operating mode selection (Manual/Off/Automatic) for each pump via touch display Potential-free contacts (changeover contact) for collective run and fault signals (SBM/SSM), individual operation and individual fault signals (EBM/ESM) and dry running signal for each pump Evaluation relay (for each pump) for the connection of submersible electrodes for low-water cut-out switchgear (detachable for each pump with separated boreholes) Digital inputs for switching external systems ON/OFF, anti-frost protection alarm signal, setpoint switchover** Analogue input 0/4-20 mA for external setpoint adjustment or control mode (only in version CC…FC and possible only with single-pump operation) Overload protection via thermal winding contact, motor protection via motor protection switch/in star-delta start-up, starting from 5.5 kW via thermal overload relay (optional: PTC/PT100 triggering available) PID controller, automatic pump alteration and service life optimisation for multi-pump systems Three setpoints are selectable by default Automatic fault-actuated switchover to idle pump Short test run of pump(s) during standstill, pilot pump function Automatic, load-sensitive cut-in of peak-load pump depending on the programmable control variables Programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system deactivation Signal and one pump at speed adjustable on frequency converter Additional charge for optional modules (installation in factory or later after technical clarification): Temperature module For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Modbus RTU, Profibus, LON bus, CAN bus, Ethernet, others on request. Signal converter for external remote setpoint adjustment or control mode using 0/2 – 10 V signals. Evaluation relay for PTC/PT100. Buffered power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. * on-site potential-free NC contact ** on-site potential-free NO contact Order example: W-CTRL-CC-WP-2x20,0A-T4-DOL-FC-BM-PKG Switchgear for 2 pumps with max. rated pump current of 20.0 A WP = version for borehole pump applications (well pump), contains the equipment described above T4 = mains connection 3~400 V DOL = activation type of the pump: direct FC = with frequency converter & sine filter BM = designed as switch cabinet floor model PKG = with packaging Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	W-CTRL-CC-WP-2x72,0A-T4-SD-WM-PKG	2540293
	Wilo-Comfort Controller for connecting pumps for water supply from bore holes and tanks. Fully electronic Comfort Controller (CC) in steel sheet housing as floor model or for wall fixation, RAL 7035 (structure), protection class IP54, completely wired. Switchgear suitable for connection to three-phase networks 3/PE 400 V/50 Hz in accordance with IEC 60038 (other voltages on request). Specially adjusted for borehole pumps from the Wilo catalogue. The Comfort Controller CC consists of: Internal power supply CPU (+ backup battery) Analogue/digital modules Power section with fuses, contactors and motor-protection equipment Graphics-capable touch display with 3-colour backlight for indicating the operating status operation/fault/acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, diagram function Main switch, internal Manual-0-Automatic service selector on each pump Operating mode selection (Manual/Off/Automatic) for each pump via touch display Potential-free contacts (changeover contact) for collective run and fault signals (SBM/SSM), individual operation and individual fault signals (EBM/ESM) and dry running signal for each pump Evaluation relay (for each pump) for the connection of submersible electrodes for low-water cut-out switchgear (detachable for each pump with separated boreholes) Digital inputs for switching external systems ON/OFF, anti-frost protection alarm signal, setpoint switchover** Analogue input 0/4-20mA for external setpoint adjustment Overload protection via thermal winding contact, motor protection via motor protection switch/in star-delta start-up, starting from 5.5 kW via thermal overload relay (optional: PTC/PT100 triggering available) PID controller, automatic pump alteration and service life optimisation for multi-pump systems Three setpoints are selectable by default Automatic fault-actuated switchover to idle pump Short test run of pump(s) during standstill, pilot pump function Automatic, load-sensitive cut-in of peak-load pump depending on the programmable control variables Programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system deactivation Signal and one pump at speed adjustable on frequency converter Additional charge for optional modules (installation in factory or later after technical clarification): Temperature module For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Modbus RTU, Profibus, LON bus, CAN bus, Ethernet, others on request. Signal converter for external remote setpoint adjustment or control mode using 0/2 – 10 V signals. Evaluation relay for PTC/PT100. Buffered power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. * on-site potential-free NC contact ** on-site potential-free NO contact Order example: W-CTRL-CC-WP-2x20,0A-T4-DOL-BM-PKG Switchgear for 2 pumps with max. rated pump current of 20.0 A WP = version for borehole pump applications (well pump), contains the equipment described above T4 = mains connection 3~400 V DOL = activation type of the pump: direct BM = designed as switch cabinet floor model PKG = with packaging Scope of delivery Switchgear Installation and operating instructions Circuit diagram
Pressure control (2)
Pressure switching
Pressure switching	Pressure switching 0 – 16 bar	2501639
Pressure switching	In the shunt on the kit attached to the pipework on the pressure side for mounting an automatic pressure-dependent single-pump system in combination with an ER-1 switchgear that can evaluate the signal of the pressure switch. The diaphragm pressure vessel placed on top is for buffering leakages. Note The required connection cable is to be provided onsite. Scope of delivery Red brass and/or brass fittings Diaphragm pressure vessel 8 l, PN16 Pressure gauge 0-16 bar Pressure switch 0-16 bar
Sensor kit
Sensor kit	Sensor kit	2501886
Sensor kit	For mounting an automatic two-pump system with pressure-dependent operation. The pressure sensor measures the applied pressure and delivers signals for switchgear with a 4 – 20 mA input. Notice Take care to ensure that a non-return valve is placed between pump and kit! Scope of delivery Red brass and/or brass fittings Diaphragm pressure vessel 8 l, PN 16 Stainless steel pressure sensor 4-20 mA Pressure gauge Ball valve Installation and operating instructions
Break tank/accessories (1)
Level indicator AF 400
Level indicator AF 400	Level indicator AF 400	2512862
Level indicator AF 400	The level indicator makes it possible to display the cistern level when using rainwater. The integrated level sensor records the percentage cistern volume up to a level of 5 m. Separate unit without communication with the AF400 Scope of delivery Ready-for-connection switchbox 230 V / 50Hz for installation in buildings Level sensor 0 – 5 mWS with 20m-long cable for connection with the level indicator Installation and operating instructions
Cable (51)
Motor cable
Motor cable	Motor cable for process water 4 x 35 mm²	4046684
	Flexible copper cable for the freely selectable extension of the cable attached to the pump motor. Suitable for use in drinking water. Scope of delivery Round cable with bare cable ends. Available in length increments of 1 m
	Motor cable for process water 4 x 50 mm²	4051974
	Flexible copper cable for the freely selectable extension of the cable attached to the pump motor. Suitable for use in drinking water. Scope of delivery Round cable with bare cable ends. Available in length increments of 1 m
	Motor cable for process water 4 x 25 mm²	4046682
	Flexible copper cable for the freely selectable extension of the cable attached to the pump motor. Suitable for use in drinking water. Scope of delivery Round cable with bare cable ends. Available in length increments of 1 m
	Earth cable, 1 x 25 mm²	4075939
	Flexible copper cable for the freely selectable extension of the cable attached to the pump motor. Suitable for use in drinking water. Scope of delivery Round cable with bare cable ends. Available in length increments of 1 m
	cable ÖLFLEX CY 2x1,0 gr round screened	6007452
	Round cable, 2-core, with bare cable ends for extension of the signal cable located on the pump. The flexible PVC pipe is colour-coded, shielded and available in lengths measured in intervals of 1 m each.
Motor cable extension (motor cable connector kit)
Motor cable extension (motor cable connector kit)	Motor cable connector kit	4087148
Motor cable extension (motor cable connector kit)	NO VALUE1
Motor cable extension (motor cable kit QC)
Motor cable extension (motor cable kit QC)	Motor cable kit QC 4 x 1.5 mm², 1.5 m	4096206
	Quick connection motor cable for replacement of the standard cable with free cable ends of Wilo submersible pumps TWU 4-…-C; TWI 4-…-C, and TWI 6-…-C (with 4" motor). The kit enables a simple and rapid retroactive extension with quick-connect cables (available separately). Scope of delivery Flat cable with plug connections Note: This cable is not intended for use with QC pumps.
	Motor cable kit QC 4 x 1.5 mm², 2.5 m	4096207
	Quick connection motor cable for replacement of the standard cable with free cable ends of Wilo submersible pumps TWU 4-…-C; TWI 4-…-C, and TWI 6-…-C (with 4" motor). The kit enables a simple and rapid retroactive extension with quick-connect cables (available separately). Scope of delivery Flat cable with plug connections Note: This cable is not intended for use with QC pumps.
Motor cable for drinking water (material sold by the metre)
Motor cable for drinking water (material sold by the metre)	motor cable for drinking water 4 x 10 mm²	6019018
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	motor cable for drinking water 4 x 4 mm²	6019995
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	motor cable for drinking water 4 x 16 mm²	6022013
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	motor cable for drinking water 4 x 25 mm²	6038861
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BB-F 3G1,5 round ACS	6045113
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BB-F 4G1,5 round ACS	6045510
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BB-F 4G2,5 round ACS	6045111
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BB-F 4G4 round	6007626
	Round cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G6 flat	6007614
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G25 flat	6007547
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G4 flat	6007618
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G10 flat	6007624
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G2,5 flat	6007636
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G50 flat	6020298
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
	cable S07BBH2-F 4G16 flat	6020318
	Flat cable with bare cable ends for extension of the motor cable located on the pump (max. immersion depth: 200 m). The cable is suitable for drinking water applications and available in lengths measured in intervals of 1 m each. Flexible copper cable in accordance with Class E of ACS 04 ACC Ll 021, NFC 15-100 AD8, BS 6920, IEC 60332-1.
Motor cable for drinking water 6 inch motor
Motor cable for drinking water 6 inch motor	Cable kit for 6 inch motors 4 x 4 mm², 10 m	6036603
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 4 mm², 20 m	6036604
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 4 mm², 30 m	6036605
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 4 mm², 40 m	6036606
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 4 mm², 50 m	6036607
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 8 m	6030798
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 10 m	6037500
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 20 m	6037501
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 30 m	6037502
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 40 m	6037503
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
	Cable kit for 6 inch motors 4 x 8,4 mm², 50 m	6037504
	Kit for replacing existing connection cable on the motor. Consisting of a flat cable with connector on the motor side and bare cable end on the switchbox end. Cable set is factory-wired. Can be used for 1~230 V and 3~400 V. Suitable for use in drinking water
Quick Connect cable
Quick Connect cable	Motor cable QC 4 x 1,5 mm², 10 m	4087121
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 1,5 mm², 30 m	4087122
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 1,5 mm², 50 m	4087129
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 1,5 mm², 80 m	4087130
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 1,5 mm², 100 m	4087131
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 2,5 mm², 50 m	4087132
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 2,5 mm², 80 m	4087136
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 2,5 mm², 100 m	4087137
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
	Motor cable QC 4 x 1,5 mm², 20 m	4440091
	Quick connection motor cable for quick and easy cable extension for Wilo submersible pumps in Quick Connect version or in combination with a Quick Connect kit. The Quick Connection motor cable is suitable for pumps with a nominal rated power of up to 7.5 kW maximum. The existing cable coupling enables direct connection to the Quick Connect plug of the QC pump or the QC kit. Scope of delivery Round cable with cable coupling Rope Cable terminal Cable ties
Shrink sleeving connections
Shrink sleeving connections	heat-shrink connections 4 x 1.5 mm² and 2.5 mm²	4029677
	Heat shrink cable sleeve for sealing a connection of two open cable ends. Scope of delivery Kit consisting of 4 heat-shrink connectors with accessories
	heat-shrink connections 4 x 10 mm² and 16 mm²	4029678
	Heat shrink cable sleeve for sealing a connection of two open cable ends. Scope of delivery Kit consisting of 4 heat-shrink connectors with accessories
	heat-shrink connections 4 x 4.0 mm² and 6.0 mm²	4059213
	Heat shrink cable sleeve for sealing a connection of two open cable ends. Scope of delivery Kit consisting of 4 heat-shrink connectors with accessories
Splicing kit
Splicing kit	Sealing kit 4 x 1.5 to 4 x 10 mm²	4065698
	Kit for the safe connection of two open cable ends under water. Scope of delivery 2 plastic sumps 2 casting resin components 4 cable clamps
	Sealing kit 4 x 10 to 4 x 25 mm²	4065699
	Kit for the safe connection of two open cable ends under water. Scope of delivery 2 plastic sumps 2 casting resin components 4 cable clamps
	Sealing kit 3 x 1.5 to 4 x 1.5 mm²	6001126
	Sealing kit for the water pressure-tight connection of power supply cables for submersible pumps. Scope of delivery 1 sleeve (plastic) 2 caps (plastic) 7 crimp connectors 1 emery cloth 1 pcs. kit 1 pcs. self-fusing tape 1 bag with resin and hardener 1 funnel Processing notes The sealing mixture of resin and hardener must be processed at an ambient temperature of at least 20 °C. The hardening time is around 8 hours at 20 °C. around 4 hours at 30 °C. The finished cable connection must harden completely before it is used under water!
	Sealing kit 3 x 2.5 to 7 x 2.5 mm²	6001128
	Sealing kit for the water pressure-tight connection of power supply cables for submersible pumps. Scope of delivery 1 sleeve (plastic) 2 caps (plastic) 7 crimp connectors 1 emery cloth 1 pcs. kit 1 pcs. self-fusing tape 1 bag with resin and hardener 1 funnel Processing notes The sealing mixture of resin and hardener must be processed at an ambient temperature of at least 20 °C. The hardening time is around 8 hours at 20 °C. around 4 hours at 30 °C. The finished cable connection must harden completely before it is used under water!
	Sealing kit 3 x 4 - 4 x 4 mm²	6001129
	Sealing kit for the water pressure-tight connection of power supply cables for submersible pumps. Scope of delivery 1 sleeve (plastic) 2 caps (plastic) 7 crimp connectors 1 emery cloth 1 pcs. kit 1 pcs. self-fusing tape 1 bag with resin and hardener 1 funnel Processing notes The sealing mixture of resin and hardener must be processed at an ambient temperature of at least 20 °C. The hardening time is around 8 hours at 20 °C. around 4 hours at 30 °C. The finished cable connection must harden completely before it is used under water!
Level control (21)
Float switch WA
Float switch WA	Float switch WA65 with 5 m cable	503211390
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 10 m cable	503211893
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 20 m cable	2004431
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 30 m cable	2004432
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA KR1 S with 5 m cable	6082806
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA KR1 S with 10 m cable	6082807
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
Float switch WAO
Float switch WAO	Float switch WAO 65, 5 m cable	503211595
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up OFF, down ON
	Float switch WAO 65, 10 m cable	2006027
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up OFF, down ON
	Float switch WAO 65, 20 m cable	2004429
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up OFF, down ON
	Float switch WAO 65, 30 m cable	2004430
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up OFF, down ON
Immersion probe
Immersion probe	Submersible electrode, 3 m	500183799
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 4 m	2516278
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 5 m	500937990
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 10 m	2501937
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 20 m	2516283
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 25 m	2000601
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 30 m	2514045
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 35 m	2516284
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 40 m	2516285
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode, 50 m	2500315
	Signal transmitter with connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. The H07 cable is approved for drinking water applications.
	Submersible electrode without cable	64873
	Signal transmitter without connection cable for protection against low water level for borehole pumps. To be connected to a switchgear with a triggering relay. Notice: The connection cable must be provided and connected by the customer!
Level control/accessories (1)
Connection cable for submersible electrode
Connection cable for submersible electrode	Connection cable for subm. electrode	64904
Connection cable for submersible electrode	Connection cable for connecting a submersible electrode [only for Art. 64873]. Note Depending on the submersible electrode, a suitable connection material is required.

With Wilo as your partner, you can not only be sure of choosing high-quality product solutions, but also of benefiting from a comprehensive, worry-free package of well thought-out services. We collaborate to develop a service concept tailored to your individual needs; with our expertise and personal consultancy, we make sure that the operation of your systems is as energy-efficient, reliable and economical as possible. All the while our competent Wilo service technicians are ready to assist you with fast, reliable and on-time support.

Recommended services
Wilo-Live Assistant	Wilo-Live Assistant Service	2216415
	The Wilo-Live Assistant is a technical advisor at your side during pump service. By using the Wilo-Live Assistant, our expert advisers can support you in the boiler or equipment room via video transmission – live and in real time. You use your smartphone to show the installation set-up, while the Wilo expert follows everything on their screen. They can see the components as well as other details and can thus determine where the fault or breakdown originates. We prevent downtime and ensure operational reliability of your pumps and systems! The Wilo-Live Assistant includes: Interactive live support via video chat Direct contact with an expert Just-in-time solution to ensure maximum operational reliability of your pumps and systems
More suitable services
Supervision	Supervision borehole/submersible pump TWI 6"-8"	2219332
	Wilo supports during the concept phase to ensure quality work and cost efficiency. Our competent and qualified Wilo Service will support you with recommendations and technical advice throughout the entire project. Supervision includes: Regular on-site visits ensure the quality of information and advice Technical consultancy, also available on site Status report with recommendations after the visit Comprehensive support from a Wilo expert
Commissioning	Commissioning borehole/submersible pump TWI 6"-8"	2219398
	For perfect functioning of the pump(s) / system(s), it is recommended to have the commissioning carried out by the works' own WILO SE Customer Service Department. Optimum setting and efficient operation of the system are ensured as a result. Commissioning is comprised of the following points: Commissioning of system(s) according to checklist Parameterisation and setting of switchgear Testing and adaptation of initial compressing of pressure tanks (filling up to 80 litres incl.) Functional check of fitted system(s) Practice-oriented operation instruction Wilo commissioning protocol The price for commissioning only applies to system(s) which have been installed in accordance with the installation and operating instructions and state-of-the-art technology. No costs for any materials which may be required are included.
Maintenance	Maintenance BASIC borehole/submersible pump TWI 6"-8"	2219538
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance COMFORT borehole/submersible pump TWI 6"-8"	2219500
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during normal service hours) Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance PREMIUM borehole/submersible pump TWI 6"-8"	2219553
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Checking the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during and outside normal service hours) Software updates Includes wearing parts Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
Repair	Repair borehole/submersible pump TWI 6"-8"	2219621
	Wilo Service draws on their competence and experience while consulting on site to decide whether the pump can actually be repaired on site or has to be sent in for a factory repair. Wilo also provides spare parts or a replacement pump to restore the operational reliability of the system. Repair includes: Verification and elimination of error causes by experienced Wilo experts Non-binding estimate for repairs Electric-hydraulic test run to ensure correct data regarding functionality, quality and performance of the pump or system Coating of various pump or system components for an optimised efficiency factor Use of genuine spare parts only Documentation of the repair in the service report

Sub TWI 6.30-26-C-SD

Installation and operating instructions

Wilo-Sub TWI 4-6

Wilo-Sub TWI 4-6

Fittings (3)

Pressure gauge

Pressure gauge

Installation/setup (1)

Cable terminal

Cable terminal

Motor cooling (2)

Cooling jacket, horizontal

Cooling jacket, horizontal

Cooling jacket, vertical

Cooling jacket, vertical

Pressure control (6)

Pressure reducer

Pressure reducer

Pressurised expansion tanks (18)

Diaphragm pressure vessel DT5 junior

Diaphragm pressure vessel DT5 junior

Diaphragm pressure vessel type D

Diaphragm pressure vessel type D

Diaphragm pressure vessel type DE

Diaphragm pressure vessel type DE

Pump control (1)

Wilo-EFC

Wilo-EFC

Pump control/accessories (1)

Pt 100 sensor

Pt 100 sensor

Pump control/Comfort control system (4)

W-CTRL-CC-WP

W-CTRL-CC-WP

Pressure control (2)

Pressure switching

Pressure switching

Sensor kit

Sensor kit

Break tank/accessories (1)

Level indicator AF 400

Level indicator AF 400

Cable (51)

Motor cable

Motor cable

Motor cable extension (motor cable connector kit)

Motor cable extension (motor cable connector kit)

Motor cable extension (motor cable kit QC)

Motor cable extension (motor cable kit QC)

Motor cable for drinking water (material sold by the metre)

Motor cable for drinking water (material sold by the metre)

Motor cable for drinking water 6 inch motor

Motor cable for drinking water 6 inch motor

Quick Connect cable

Quick Connect cable

Shrink sleeving connections

Shrink sleeving connections

Splicing kit

Splicing kit

Level control (21)

Float switch WA

Float switch WA

Float switch WAO

Float switch WAO

Immersion probe

Immersion probe

Level control/accessories (1)

Connection cable for submersible electrode

Connection cable for submersible electrode

Recommended services

Wilo-Live Assistant

More suitable services

Supervision

Commissioning

Maintenance

Repair