Comfort-Vario COR-3 MVIE 7003/1/SCe (3~400 V, 50/60 Hz)

Folha de especificações

Dados hidráulicos
  • Comando
    Com conversor de frequência
  • Pressão de funcionamento máx. p
    16 bar
  • Ligação do tubo do lado da pressão DNd
    DN 200
  • Ligação do tubo do lado da sucção DNs
    DN 200
  • Escala
    3
  • Número de bombas de reserva
    1
  • Número de bombas de serviço
    2
  • Temperatura mín. dos líquidos Tmin
    3 °C
  • Temperatura máx. dos líquidos Tmax
    60 °C
  • Temperatura ambiente mín. Tmin
    5 °C
  • Temperatura ambiente máx. Tmax
    50 °C
Dados do motor
  • Tolerância de tensão
    400/50:+/-10%_380/60:+/-10%_460/60:+/-10%
  • Classe de isolamento
    F
  • Tipo de proteção
    IP55
  • Potência nominal do motor P2
    15000.00 W
  • Corrente nominal IN
    39.90 A
  • Rendimento do motor ηm 100 % ηM 100%
    90.7
Materiais
  • Corpo da bomba
    EN-GJL-250
  • Impulsor
    1.4301
  • Veio
    1.4057
  • Empanque mecânico
    U3BE3GG
  • Material do vedante
    EPDM
Informações sobre os pedidos de encomenda
  • Marca
    Wilo
  • Designação do produto
    Comfort-Vario COR-3 MVIE 7003/1/SCe (3~400 V, 50/60 Hz)
  • Número EAN
    4048482968537
  • Número de artigo
    2552085
  • Peso líquido aprox. m
    1096 kg
  • Peso bruto aprox. m
    1224.0 kg
  • Comprimento com embalagem
    2400 mm
  • Altura com embalagem
    1950 mm
  • Largura com embalagem
    1720 mm
  • Propriedades da embalagem
    Embalagem de transporte
  • Tipo de embalagem
    Patins de transporte
  • Quantidade mínima de encomenda
    1

Texto de especificação

Compact pressure boosting system according to DIN 1988 and DIN EN 806, for direct or indirect connection. Consisting of non self-priming, switched in parallel, vertically-mounted stainless steel high-pressure centrifugal pumps in glanded versions, for which each pump is fitted with a frequency converter. Ready for connection with stainless steel pipework, mounted on a base frame, including control device with all necessary measurement and adjustment equipment.

For fully automatic water supply and pressure boosting in residential, commercial and public buildings, hotels, hospitals, department stores and for industrial systems.

For pumping drinking water, process water, cooling water, fire water (apart from fire-extinguishing systems in accordance with DIN 14462 and with the approval of the local fire safety authorities) or other types of industrial water that do not attack the materials either chemically or mechanically and do not contain abrasive or long-fibre constituents.

Special features/product benefits

• High energy system efficiency thanks to IE4 motor and optimised hydraulics

• Disproportionately large frequency converter control range from 25 Hz up to a maximum of 60 Hz for a large field of application

• High reliability thanks to various protective features including overload protection, dry-running protection and automatic deactivation.

• Easy setting and operation with the SCe control panel thanks to LCD display, and green knob for adjustment.

• Ready for building automation integration with the SCe control panel via Modbus

Equipment/function

2-4 pumps per system of the MVIE (70 or 95) series with speed controlled motor via integrated frequency inverter on each pump.

SCe control panel ensures automatic control of the complete booster set.

All is mounted on galvanized steel height adjustable base frame.

All components in contact with fluid are corrosion resistant.

On pressure side:

• Shut-off valve

• Non return valve

• Check-valve at each pump

• Diaphragm pressure vessel 8 l, PN 16

• Pressure sensor 4..20mA

• Pressure gauge

On suction side

• Shut-off valve

• Pressure sensor 4..20mA

• Pressure gauge

Smart-Controller (SCe) in a sheet metal enclosure, protection class IP 54 consisting of an internal power supply unit, microprocessor with Soft PLC, analogue and digital inputs and outputs, for control of electronic pumps with frequency converters.

A working area of 1 m around the system is recommended in order to facilitate the maintenance process.

Operation/ display

• LC display (backlit) for display of the operating data, controller parameters, operating statuses of the pumps, error messages and history log

• Menu navigation with symbols and menu numbers

• LEDs for display of the system status (operation/fault)

• Factory-preset parameters for easy commissioning/start-up

• Configuration of operating parameters and acknowledgement of fault signals using red-button technology

• Lockable main switch

• Operation selectable with / without standby pump by customer service

• Elapsed time indicator for each pump and for entire system

• Switching cycle counter for each pump and for entire system

• Fault log for the last 16 faults

Control

• Fully automatic control for 1 to 4 frequency-controlled pumps by means of setpoint/actual value comparison

• Setpoint changeover: 2nd setpoint can be activated by contact

• External remote setpoint adjustment by 4…20 mA signal

• Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variable pressure - constant, p-c or pressure - variable, p-v

• 2 parameter sets selectable, easy menu (setpoint & control mode) or expert menu (operation and control parameters)

• Operating mode of the pumps freely selectable (manual, off, automatic)

• Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours

• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

• Automatic, configurable pump test run (pump kick)

• Can be activated/deactivated

• Time between two test runs is freely programmable

• Disabling times can be programmed as desired

• Speed can be adjusted as desired

Monitoring

• Actual value of the system is output via a 0-10 Volt analogue signal for external measurement / display applications, 10 Volt depending on the sensor range value

• 4-20mA sensor signal (conductivity test of the sensor cable) for control variable actual value

• The pump mains power feed is protected via the circuit breaker

• Automatic changeover to the standby pump in the event of a operating pump fault

• Monitoring of maximum and minimum system values with adjustable time delays and limits

• Zero-flow test for switching off the system when no water is being drawn off (adjustable parameters)

• Pipe filling function for filling empty pipes (initial filling of the consumer network)

• Protection against low water level via contact e.g. for float switch or pressure switch

Interfaces

• Potential-free contacts for SBM/SSM collective operation and collective fault signals

• Logical reversal can be applied to SBM and SSM

• Contacts for external on/off, low water and 2nd Setpoint

• External on/off via contact for deactivation of the system's automatic mode

Optional accessories (factory installation or retrofitting after technical checks)

• Manual-0-Automatic switch Preselection of the operating mode of each pump and manual operation in the event of a controller fault "Manual" (emergency/test mode available at mains power, motor protection available), "O" (pump switched off – cannot be switched on using the controller) and "Auto" (pump enabled for automatic mode via the controller)

• Evaluation relay for PTC motor protection

• Individual operation and fault signal, low-water signal

• Signal converter for 0/ 2-10V to 0/ 4-20mA

• Soft starter for peak-load pumps

• Connection to BMS systems in accordance with VDI 3814

Recommended accessories (to be ordered separately)

• Optional WMS low-water cut-out switchgear kit;

• Flexible connection lines or expansion joints

• Break tank for system separation

• Diaphragm pressure vessel

• Threaded caps for systems with threaded joint tubing

Bus systems (optional)

• BACnet, LON bus, Modbus RTU

Standards followed

• Specifications for drinking water installations (TRWI) DIN 1988 (EN806)

• Diaphragm pressure vessel/ diaphragm expansion tank DIN 4807

• Electronic Equipment for Use in Power Installations EN 50178

• Electrical Equipment of Machines EN 60204-1

• Household and Similar Electrical Appliances - Safety EN 60335-1

• Low-voltage switchgear combinations EN 60439-1/ 61439-1

• EMC - Immunity for Industrial Environments EN 61000-6-2

• EMC - Emission Standard for Residential, Commercial and Light-Industrial Environments (EN 61000-6-3)

Dados de funcionamento
  • Fluido
    Water
  • Número de bombas
    3
  • Pressão de funcionamento máxima PN
    16 bar
  • Pressão de alimentação
    10 bar
Dados do motor
  • Potência nominal do motor P2
    15000.00 W
  • Corrente nominal IN
    39.90 A
  • Velocidade nominal n
    2900 rpm
  • Classe de isolamento
    F
  • Tipo de proteção do motor
    IP55
  • Tipo de protecção do aparelho de distribuição
    IP54
Materiais
  • Corpo da bomba
    EN-GJL-250
  • Impulsor
    1.4301
  • Veio
    1.4057
  • Vedante do veio
    U3BE3GG
  • Material do vedante
    EPDM
  • Material da tubagem
    1.4571
Dimensões de instalação
  • Ligação do tubo do lado da sucção DNs
    DN 200
  • Ligação do tubo do lado da pressão DNd
    DN 200
Informações sobre os pedidos de encomenda
  • Marca
    Wilo
  • Designação do produto
    Comfort-Vario COR-3 MVIE 7003/1/SCe (3~400 V, 50/60 Hz)
  • Peso líquido aprox. m
    1096 kg
  • Número de artigo
    2552085

Informações de encomenda

Information for order placements
  • Marca
    Wilo
  • Designação do produto
    Comfort-Vario COR-3 MVIE 7003/1/SCe (3~400 V, 50/60 Hz)
  • Número EAN
    4048482968537
  • Número de artigo
    2552085
  • Peso bruto aprox. m
    1224.0 kg
  • Peso líquido aprox. m
    1096 kg
  • Comprimento total L
    2200.0 mm
  • Altura sem embalagem H
    1708 mm
  • Cor
    verde/preto/prata
  • Propriedades da embalagem
    Embalagem de transporte
  • Tipo de embalagem
    Patins de transporte
  • Número por camada
    1
  • Largura sem embalagem L
    1640.0 mm
  • Quantidade mínima de encomenda
    1
  • Quantidade por palete
    1

PDF: Comfort-Vario COR-3 MVIE 7003/1/SCe (3~400 V, 50/60 Hz)

Configurar

Selecção da página

Informações opcionais

Poderá indicar os dados pessoais que pretende que figurem no cabeçalho.

Memorizar