Wilo-SiBoost Smart 1 MVISE

Low noise water-supply unit ready for connection with a vertically arranged non-self-priming glandless stainless steel high-pressure multistage centrifugal pump of MVISE series with an integrated water-cooled frequency inverter.

Fully automatic water supply and pressure boosting in inlet mode, either from the public water supply network or from a tank at least 0.5 meter above the pump, for domestic, commercial, industrial and municipal applications (a standby pump to be provided to comply with DIN 1988 and DIN EN 806).

Approved fluids are generally waters which do not attack the materials used, neither chemically nor mechanically, and do not contain any abrasive or long-fiber constituents like:

• Drinking water
• Cooling water
• Process water
• Firefighting water (apart from fire-fighting systems in accordance with DIN 14462 and with the approval of the local fire safety authorities)

1 pump of the MVISE series with glandless motor speed controlled via integrated frequency inverter mounted on galvanized steel height adjustable base frame.

All components in contact with fluid are corrosion resistant.

On pressure side:

• Shut-off valve
• Non return valve
• Check-valve
• Diaphragm pressure vessel 8 l, PN 16
• Pressure sensor 4..20mA
• Pressure gauge

On suction side:

• Pressure sensor 4..20mA
• Pressure gauge

• Mains connections 3~400 V, 50 Hz
• Max fluid temperature +50 °C
• Max. ambient temperature 40 °C
• Operating pressure 16 bar
• Inlet pressure 6 bar
• Nominal connection diameters Rp 1¼ - Rp 1½
• Speed range 1100 - 2750 rpm
• Protection class IP 44

MVISE 2-8 m3/h

• Pump housing in 1.4301 [Aisi 304]
• Hydraulics in 1.4301 [Aisi 304]
• Gasket EPDM

Base frame: galvanized steel with height-adjustable vibration absorbers for comprehensive insulation against structure-borne noise as well as integrated lifting points

Pipework: complete pressure-side pipework made of stainless steel, suitable for the connection of all piping materials used in building services. The pipework is dimensioned according to the overall hydraulic performance of the pressure boosting system.

Pumps: 1 pump from the MVISE 2, 4, 8 series is used. The water-cooled frequency inverter on the pump motor enables continuous auto control between 20 Hz and a maximum of 50 Hz for all pumps of these series. All pump parts in contact with fluid are made of stainless steel.

Valves: the pump is fitted on the pressure side with a check valve with DVGW approval mark and a DVGW-approved non-return valve

Diaphragm pressure vessel: 8 l/PN 16 arranged on the discharge side with a diaphragm made of butyl rubber, with DVGW/KTW approval, completely safe in accordance with food safety laws; for testing and inspection purposes, with a ball valve with drain and throughflow fitting with DVGW/KTW approval in accordance with DIN 4807

Pressure monitoring: 2 Pressure sensors: 4..20 mA, located on the pressure and suction sides.

Pressure indication: Pressure gauge arranged on the suction and the discharge sides

Other versions on request

• Factory-mounted, ready-for-connection pressure-boosting system checked for functionality and impermeability
• Installation and operating instructions

Other mains connections on request

Inlet pressure

The maximum inlet pressure (see Technical data) is to be observed for the system configuration. The maximum permissible inlet pressure is calculated from the maximum operating pressure of the system minus the maximum pump delivery head at Q = 0.

Always observe the specifications in DIN 1988 (EN 806) when using and operating the pressure boosting system.

Pressure reducer

Fluctuating inlet pressure is compensated by the speed control integrated into the pump as long as the pressure fluctuation is not greater than the difference between the setpoint pressure value and the zero-delivery head of the single pump at minimum speed (operation at 20 Hz or 25 Hz). If the pressure fluctuation is greater, a pressure reducing valve must be installed upstream of the system.

Residual-current devices

When installing residual-current-operated protection switches in conjunction with frequency converters, bear in mind that only universal-current-sensitive residual-current-operated protection switches in accordance with DIN/VDE 0664 are to be fitted.

Wilo-WMS low-water cut-out switchgear

The series Helix VE pump being used is already equipped with an integrated dry-running detection as safety equipment for the pump.

Details about electronics/EMC

Single-pump system up to and including 7.5 KW motor power:

• Emitted interference in compliance with EN 61000-6-3
• Interference resistance in compliance with EN 6100-6-1

Notice: Systems to be utilised in residential buildings must be installed by personnel who have completed EMC training.

• Mains connections 3~400 V, 50 Hz
• Max fluid temperature +50 °C
• Max. ambient temperature 40 °C
• Operating pressure 16 bar
• Inlet pressure 6 bar
• Nominal connection diameters Rp 1¼ - Rp 1½
• Speed range 1100 - 2750 rpm
• Protection class IP 44

MVISE 2-8 m3/h

• Pump housing in 1.4301 [Aisi 304]
• Hydraulics in 1.4301 [Aisi 304]
• Gasket EPDM

Base frame: galvanized steel with height-adjustable vibration absorbers for comprehensive insulation against structure-borne noise as well as integrated lifting points

Pipework: complete pressure-side pipework made of stainless steel, suitable for the connection of all piping materials used in building services. The pipework is dimensioned according to the overall hydraulic performance of the pressure boosting system.

Pumps: 1 pump from the MVISE 2, 4, 8 series is used. The water-cooled frequency inverter on the pump motor enables continuous auto control between 20 Hz and a maximum of 50 Hz for all pumps of these series. All pump parts in contact with fluid are made of stainless steel.

Valves: the pump is fitted on the pressure side with a check valve with DVGW approval mark and a DVGW-approved non-return valve

Diaphragm pressure vessel: 8 l/PN 16 arranged on the discharge side with a diaphragm made of butyl rubber, with DVGW/KTW approval, completely safe in accordance with food safety laws; for testing and inspection purposes, with a ball valve with drain and throughflow fitting with DVGW/KTW approval in accordance with DIN 4807

Pressure monitoring: 2 Pressure sensors: 4..20 mA, located on the pressure and suction sides.

Pressure indication: Pressure gauge arranged on the suction and the discharge sides

Other versions on request

• Factory-mounted, ready-for-connection pressure-boosting system checked for functionality and impermeability
• Installation and operating instructions

Other mains connections on request

Inlet pressure

The maximum inlet pressure (see Technical data) is to be observed for the system configuration. The maximum permissible inlet pressure is calculated from the maximum operating pressure of the system minus the maximum pump delivery head at Q = 0.

Always observe the specifications in DIN 1988 (EN 806) when using and operating the pressure boosting system.

Pressure reducer

Fluctuating inlet pressure is compensated by the speed control integrated into the pump as long as the pressure fluctuation is not greater than the difference between the setpoint pressure value and the zero-delivery head of the single pump at minimum speed (operation at 20 Hz or 25 Hz). If the pressure fluctuation is greater, a pressure reducing valve must be installed upstream of the system.

Residual-current devices

When installing residual-current-operated protection switches in conjunction with frequency converters, bear in mind that only universal-current-sensitive residual-current-operated protection switches in accordance with DIN/VDE 0664 are to be fitted.

Wilo-WMS low-water cut-out switchgear

The series Helix VE pump being used is already equipped with an integrated dry-running detection as safety equipment for the pump.

Details about electronics/EMC

Single-pump system up to and including 7.5 KW motor power:

• Emitted interference in compliance with EN 61000-6-3
• Interference resistance in compliance with EN 6100-6-1

Notice: Systems to be utilised in residential buildings must be installed by personnel who have completed EMC training.