*Toll Free

SiBoost Smart FC 2 HELIX V2205-ES | Wilo
Similar to figure

SiBoost Smart FC 2 HELIX V2205-ES

Technical data
Tender text

Compact pressure boosting system according to DIN 1988 and DIN EN 806, for direct or indirect connection. Consisting of non self-priming, switched in parallel, vertically-mounted stainless steel high-pressure multistage centrifugal pumps in glanded versions. Ready for connection with stainless steel pipework, mounted on a base frame, including control device with all necessary measurement and adjustment equipment.

For fully automatic water supply and pressure boosting in residential, commercial and public buildings, hotels, hospitals, department stores and for industrial systems.

For pumping drinking water, process water, cooling water, firefighting water (apart from fire-extinguishing systems in accordance with DIN 14462 and with the approval of the local fire protection authorities) or other types of industrial water that do not attack the materials either chemically or mechanically and do not contain abrasive or long-fibre constituents.

Special features/product benefits

  • Heavy-duty system which satisfies all the requirements of DIN 1988 (EN 806)
  • WRAS/ KTW/ ACS approval of the pumps for all parts that come in contact with the fluid (EPDM version)
  • High-efficiency pump hydraulics of the Helix V series in connection with IE3 standard motor, including 0.75 kW and larger (optional for smaller motor power)
  • Bidirectional mechanical seals in the pumps for easy maintenance
  • Flexible lantern design permits direct access to the mechanical seal
  • The spacer coupling enables the mechanical seal to be replaced without dismantling the motor (from 7.5 kW)
  • Hydraulics of entire system are pressure-loss optimised
  • Parts that come in contact with the fluid are corrosion-resistant
  • Comfort control device SC-FC, maximum degree of control with symbol-based LC display, simple navigation with clear menu and Red Button Technology for parameter setting, including a frequency converter for continuous control of the base-load pump
  • Factory inspection and default setting at optimum operating range (incl. inspection certificate in accordance with EN 10204-3.1)


  • Stainless steel high-pressure multistage centrifugal pumps of the Helix V series
  • Base frame of electrolytically galvanised steel, with height-adjustable vibration absorbers for insulation against structure-borne noise
  • Shut-off device on the suction and pressure sides of each pump
  • Non-return valve on the pressure side of each pump
  • 8 litre diaphragm pressure vessel, PN 16 including throughflow fitting in accordance with DIN 4807, pressure side
  • Pressure sensor (4 – 20 mA), pressure side
  • Pressure gauge, pressure side
  • Automatic pump control by means of a fully electronic

Smart-Controller (SC-FC) in a sheet metal enclosure, protection class IP54 consisting of internal control voltage supply unit, microprocessor with soft PLC, frequency converter, analogue and digital inputs and outputs.

A working area of 1 m around the system is recommended in order to facilitate the maintenance process.


  • LC display (backlit) for display of the operating data, controller parameters, operating statuses of the pumps, error messages and history memory
  • Menu navigation with symbols and menu numbers
  • LEDs for display of the system status (operation/fault)
  • Factory-preset parameters for easy commissioning/start-up
  • Setting of operating parameters and acknowledgement of fault signals using Red Button Technology
  • Lockable main switch
  • Operation selectable with / without standby pump by customer service
  • Elapsed time indicator for each pump and for entire system
  • Switching cycle counter for each pump and for entire system
  • Fault log for the last 16 faults


  • Fully automatic control for 1 to 4 uncontrolled pumps by means of setpoint/actual value comparison
  • Frequency converter with sine filter for infinitely variable control of the base-load pump
  • Setpoint changeover: 2nd setpoint can be activated by contact
  • External setpoint adjustment via 4…20 mA signal
  • Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the pressure - constant, p-c control variable
  • Contactors for switching on the pumps. SD versions include thermal triggering and a time relay for the star-delta combination
  • 2 parameter sets selectable, easy menu (setpoint & control mode) or expert menu (operation and control parameters)
  • Operating mode of the pumps freely selectable (manual, off, automatic)
  • Automatic, configurable pump cycling
    • Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
    • Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours
  • Automatic, configurable pump test run (pump kick)
    • Can be activated/deactivated
    • Time between two test runs is freely programmable
  • Disabling times can be programmed as desired
  • Speed can be adjusted as desired


  • Display of actual value of the system via a 0 – 10 Volt analogue signal for external measurement/display applications, 10 Volt correspond to the final sensor value
  • 4 – 20 mA sensor signal (conductivity test of the sensor cable) for control variable actual value
  • Protection of the pump motors in the DOL version: via motor protection switch; in the SD version: Fuses in combination with thermal triggering
  • Automatic switchover to the standby pump in the event of an operating pump fault
  • Monitoring of maximum and minimum system values with adjustable time delays and limits
  • Zero-flow test for switching off the system when no water is being drawn off (adjustable parameters)
  • Pipe filling function for filling empty pipes (initial filling of the consumer network)
  • Protection against low water level via contact e.g. for float switch or pressure switch


  • Potential-free contacts for SBM/SSM collective operation and collective fault signals
  • Logic reversal can be applied to SBM and SSM
  • Contacts for external on/off, low water and 2nd setpoint
  • External on/off via contact for deactivation of the system's automatic mode

Optional accessories (factory installation or retrofitting after technical checks)

  • Manual-0-Automatic switch Preselection of the operating mode of each pump and manual operation in the event of a controller fault "Manual" (emergency/test mode available at mains power, motor protection available), "O" (pump switched off – cannot be switched on using the controller) and "Auto" (pump enabled for automatic mode via the controller)
  • Evaluation relay for PTC motor protection
  • Individual operation and fault signal, low-water signal
  • Signal converter for 0/2 –10 V to 0/4 – 20 mA
  • Soft starter for peak-load pumps
  • Connection to BMS in accordance with VDI 3814

Recommended accessories (to be ordered separately)

  • Optional WMS low-water cut-out switchgear kit
  • Flexible connection pipes or compensators
  • Break tank for system separation
  • Diaphragm pressure vessel
  • Threaded caps for systems with threaded joint tubing

Bus systems (optional)

  • BACnet, LON bus, Modbus RTU

Standards followed

  • Codes of practice for drinking water installations (TRWI) DIN 1988 (EN806)
  • Diaphragm pressure vessel/ diaphragm expansion tank DIN 4807
  • Electronic equipment for use in power installations EN 50178
  • Electrical equipment of machines EN 60204-1
  • Safety of household and similar electrical appliances EN 60335-1
  • Low-voltage switchgear and controlgear assemblies EN 60439-1/61439-1
  • EMC interference resistance for industrial environments EN 61000-6-2
  • EMC – Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (up to 9.0 kW, above this Emission standard for industrial environments EN 61000-6-4)
Operating data
Number of pumps 2
Fluid temperature T 3 °C
Ambient temperature T 5 °C
Maximum operating pressure PN 16 bar
Maximum inlet pressure p inl 10 bar
Motor data
Mains connection 3~400 V, 50 Hz
Rated power P2 7.5 kW
Rated current IN 13.7 A
Rated speed n 2900 1/min
Insulation class F
Protection class motor IP55
Protection class switchgear IP54
Pump housing Stainless steel
Impeller Stainless steel
Shaft Stainless steel
Shaft seal Q1BE3GG
Gasket material EPDM
Pipework material Stainless steel
Installation dimensions
Pipe connection on the suction side DNs R 3
Pipe connection on the discharge side DNd R 3
Ordering information
Brand Wilo
Product description SiBoost Smart FC 2 HELIX V2205-ES
Net weight, approx. m 447 kg
Article number 2547396

Installation and operating instructions

Wilo-SiBoost Smart (FC) ... Helix V/... Helix VE/... Helix EXCEL

Article Number 2535457
Edition 1508
Page format A4
Number of pages 1
ZIP (62 MB)

Wilo-Helix V/ FIRST V 22-36-52

Article Number 4120943
Edition 1603
Page format A4
Number of pages 1
ZIP (111 MB)

Wilo-Helix V/ FIRST V 22-36-52

Article Number 4120943
Edition 1603
Page format A4
Number of pages 15
PDF (4 MB)

Wilo-SiBoost Smart ...

Article Number 2535457
Edition 1808
Page format 209.9 x 297.0 mm
Number of pages 1343
PDF (37 MB)

Wilo-Control SC-Booster (SC, SC-FC, SCe)

Article Number 2535460
Edition 1809
Page format 209.9 x 297.0 mm
Number of pages 1795
PDF (44 MB)

Wilo-SiBoost Smart (FC) ... Helix V/... Helix VE/... Helix EXCEL

Article Number 2535457
Edition 2021-01
Page format 209.9 x 297.0 mm
Number of pages 48
PDF (3 MB)

Certification booklet

Wilo-SiBoost Smart ...

Article Number 2550649
Edition 1905
Page format 209.9 x 297.0 mm
Number of pages 16
PDF (6 MB)

Wilo-Control SC-Booster (SC, SC-FC, SCe)

Article Number 2550530
Edition 1811
Page format 209.9 x 297.0 mm
Number of pages 8
PDF (2 MB)

Certificate REACH (Documents)

REACH Regulation

Edition 2021-05
Page format 209.9 x 297.0 mm
Number of pages 4
PDF (212 KB)