Wilo-Sub TWI 6

Special features/product advantages

  • Long service life thanks to corrosion-resistant stainless steel, optionally in V4A quality
  • ACS certified for domestic hot water applications
  • A high degree of flexibility thanks to versions in the 4, 6, 8 and 10-inch area
  • High range of performance from 1 to 250 m³/h

Series description

Design

Multistage 6" submersible pump in tie strap version for vertical or horizontal installation

Application

  • For water and drinking water supply from boreholes and rainwater storage tanks
  • Process water supply
  • For municipal water supply, sprinkling and irrigation
  • Pressure boosting
  • Lowering the water level
  • For pumping water in industrial applications
  • For pumping water without long-fibre and abrasive constituents

Type key

Example:

Wilo-Sub TWI 6.18-04-C-SD
TWISubmersible pump
6Diameter of the hydraulic unit in inches ["]
18Rated volume flow [m3/h]
04Number of hydraulic stages
CSeries generation
IMotor shroud in 1.4571, motor connection via flat male tab
SDStarting mode
Without = Direct starting
SD = star-delta starting

Equipment/function

  • Multistage submersible-motor pump with radial or semi-axial impellers
  • Integrated non-return valve
  • NEMA coupling
  • Three-phase motor
  • Hermetically cast motors
  • Rewindable motors

Technical data

  • Minimum Efficiency Index (MEI) ≥ 0.4
  • Mains connection: 3~400 V, 50 Hz
  • Submerged operating mode: S1
  • Fluid temperature: 3‐30 °C
  • Minimum flow rate at motor:
    • Hermetically cast motors: 0.08 - 0.16 m/s
    • Rewindable motors (SD-R): 0.1 ‐ 0.5 m/s (depending on type)
  • Max. sand content: 50 g/m3
  • Max. number of starts: 20/h
  • Max. submersion depth:
    • Hermetically cast motors: 350 m
    • Rewindable motors: 100 m
  • Protection class: IP 68
  • Pressure connection: Rp 2½ ‐ Rp 3

Materials

  • Hydraulic housing: Stainless steel 1.4301
  • Impellers: Stainless steel 1.4301
  • Hydraulic shaft: Stainless steel 1.4057
  • Motor housing: EN‐GJL or stainless steel 1.4301
  • Motor shaft: Stainless steel 1.4305 or 1.4301

Description/design

Submersible pump with ACS approval for vertical or horizontal installation.

Hydraulics

Multistage submersible-motor pump with 4" or 6" NEMA connection and radial or semi-axial impellers with sectional construction. Integrated non-return valve. All parts that come in contact with the fluid are made of corrosion-free materials.

Motor

Three-phase motor for direct and star-delta start. Sealed, hermetically cast motor with enamel-insulated winding, resin-impregnated, or rewindable motor with PVC-insulated winding, self-lubricating bearing, with water-glycol filling.

Cooling

The motor is cooled by the pumped fluid. The motor must always be immersed when operated. The limit values for maximum fluid temperature and minimum flow velocity must be adhered to. Vertical installation is possible with or without cooling jacket. Horizontal installation must be performed in conjunction with a cooling jacket.

Pressure shroud

The pressure shroud is used for the direct installation of the unit in the pipe network. Standard models are without mounted non-return valves. The maximum inlet pressure is 10 bar.

Configuration

  • No suction mode is possible with these units!
  • The unit must be fully immersed in water during operation.

Scope of delivery

  • Hydraulics and motor ready assembled
  • 4/5/10 m connecting cable approved for drinking water (cross-section: 4x2.5 mm2 or 4x4 mm2)
  • Installation and operating instructions

Options

  • Hydraulics in stainless steel 1.4401
  • Stainless steel motor in 1.4401, 1.4408 or 1.4571
  • 60 Hz version
  • Star-delta starting
  • Rewindable motor
  • Rewindable motor with drinking water filling
  • Configured units for special versions

General notes - ErP (ecological design-) directive

The benchmark for most efficient water pumps is MEI ≥ 0.70The efficiency of a pump with a trimmed impeller is usually lower than that of a pump with the full impeller diameter. The trimming of the impeller will adapt the pump to a fixed duty point, leading to reduced energy consumption. The minimum efficiency index (MEI) is based on the full impeller diameter.The operation of this water pump with variable duty points may be more efficient and economic when controlled, for example, by the use of a variable speed drive that matches the pump duty to the system.Information on benchmark efficiency is available at www.europump.org/efficiencycharts

Duty chart

Duty chart

제품

Design

NEMA connection

Standardised connection

-

Integrated non-return valve

Without non-return valve

-

AC motor

-

Three-phase motor

Direct activation

Star-delta activation

FC operation

Motor with cast stator

Rewindable motor

Oil motor filling

-

Water-glycol motor filling

Drinking water motor filling

º

Hydraulics/motor preassembled

Application

Horizontal installation

Vertical installation

Equipment/function

Motor temperature monitoring, PT100

º

PTC motor temperature monitoring

º

Capacitor box for 1~230 V

-

Dry-running protection

º

Integrated lightning protection

-

Accessories

Bearing brackets for horizontal installation

º

Cooling jacket

º

Non-return valve

-

Pressure shroud

º

Materials

Pump housing

1.4301

Pump housing (special version)

1.4404

Impeller

1.4301

Impeller (special version)

1.4404

Motor housing

1.4301

Motor housing (special version)

1.4401

Downloads

Certification Booklet Wilo-Sub TWI

Article Number 6080451
Edition 1612
Version number 02
Page format A4
Number of pages 14

PDF (397 kB)

다운로드

Certification Booklet Wilo-EMU D/DCH/K/KD/KM/NK/SCH / Wilo-Sub TWI/TWU / Wilo-Zetos K8 (w/o motor)

Article Number 6080455
Edition 1702
Version number 02
Page format A4
Number of pages 71

PDF (1 MB)

다운로드

Certification Booklet Wilo-EMU NU/U-Motor

Article Number 6080454
Edition 1702
Version number 01
Page format A4
Number of pages 8

PDF (427 kB)

다운로드

General overview

Page format A4
Number of pages 72

PDF (46 MB)

다운로드

Clean Water

Edition 2017
Page format A4
Number of pages 24

PDF (8 MB)

다운로드

Wilo-Sub TWI 4-6

Article Number 4069717
Edition 0801
Version number 03
Page format A4
Number of pages 15

PDF (913 kB)

다운로드

제품

PDF: Wilo-Sub TWI 6

구성

페이지 선택

페이지 크기

선택적 정보

머리글에 표시 할 개인 정보를 입력 할 수 있습니다.

다운로드