Glanded twin-head pump with in-line design for pipe installation or installation on a base with built-in frequency converter for electronic control for constant or variable differential pressure (Δp-c/Δp-v), among other things.

Design:

• Single-stage low-pressure centrifugal pump
• Spiral housing in in-line design (suction and pressure ports with the same flanges in one line), flanges PN 16 – drilled acc. to EN 1092-2
• Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor)
• Pump housing and motor flange with cataphoretic coating as standard
• Mechanical seal for water feed up to T=140 °C. A glycol admixture of 20 to 40% by vol. is permitted up to Tmax = +40 °C
• Special mechanical seals for water-glycol mixtures deviating from the 20–40% glycol by volume and a fluid temperature of ≤ 40 °C or fluids other than water (additional charge).

Accessories:

• Mounting brackets for fixing to the foundation
• IR-Monitor
• IF module PLR
• IF module LON
• IF module Modbus
• IF module BACnet
• IF module CAN
• Control systems VR-HVAC/CCe-HVAC/SCe-HVAC
• Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1

Standard equipment:

• One-button manual operation level for:
• Pump On/Off
• Setpoint and speed adjustment
• Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
• Selection of operating mode in dual pump operation (main/standby operation, parallel operation)
• Configuration of operating parameters
• Fault acknowledgement
• Pump display for displaying:
• Control mode
• Setpoint (e.g. differential pressure or speed)
• Error and warning messages
• Actual values (e.g. power consumption, actual value of the sensor)
• Operating data (e.g. operating hours, energy consumption)
• Status data (e.g. status of SSM and SBM relay)
• Device data (e.g. pump name)

Additional functions:

• Interfaces: Control input "Overriding Off", "External pump cycling", analogue input 0–10 V, 2–10 V, 0–20 mA, 4–20 mA for control mode (DDC) or for remote setpoint adjustment, analogue input 0–10 V, 2–10 V, 0–20 mA, 4–20 mA for actual value signal of the pressure sensor, Infrared interface for wireless communication with the operating and service unit Wilo-IR Stick/IR-Monitor, plug-in position for Wilo IF-Module for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual pump communication
• Three-phase AC motor with frequency converter
• Integrated dual pump management
• Adjustable time interval for pump cycling
• Integrated full motor protection
• Different operating modes for heating mode (HV) or air-conditioning mode (AC)
• Access disable
• Different operation levels: Standard / Service

Materials

• Pump housing
  5.1301, EN-GJL-250
• Impeller
  5.1300, EN-GJL-200
• Lantern
• Shaft
  1.4122, X39CrMo17-1

Operating data

• Fluid media
  Water
• Min. fluid temperature T
  -20 °C
• Max. fluid temperature T
  140 °C
• Maximum operating pressure p
  16 bar
• Max. ambient temperature T
  40 °C
• Minimum efficiency index (MEI)
  0.4

Motor data

• Emitted interference
  EN 61800-3
• Interference resistance
  EN 61800-3
• Mains connection
  3~440 V, 50 Hz
• Rated power P₂
  11000 W
• Max. speed n_max
  2900 rpm
• Rated current I_N
  18.50 A
• Protection class motor
  IP55
• Insulation class
  F
• Integrated full motor protection
  yes

Installation dimensions

• Pipe connection on the suction side
  DN 80
• Pipe connection on the pressure side
  DN 80

Information for order placements

• Net weight, approx. m
  386 kg
• Brand
  Wilo
• Product description
  CronoTwin-DL-E 80/160-11/2-R1
• Article number
  2153882