DrainLift WS 50E BASIC/MINI3 V04/M06-523 | Wilo

Similar to figure

DrainLift WS 50E BASIC/MINI3 V04/M06-523

Article number: 2552864

Hydraulic data
Maximum operating pressure PN	1 bar
Min. fluid temperature T_min	3 °C
Max. fluid temperature T_max	40 °C
Min. ambient temperature T_min	3 °C
Max. ambient temperature T_max	40 °C
Switching volume V	65 l
Macerator	no

Motor data
Mains connection	1~230 V, 50 Hz
Rated current I_N	4.1 A
Protection class	IP68
Phase	1
Rated speed n	2900 1/min
Number of poles	2
Activation type	Direct On Line (DOL)
Max. switching frequency t	30 1/h
Power consumption P1(Q=max.) of selected impeller * number of pumps P1	930 W
Operating mode (non-immersed)	S3-20%
Insulation class	F

Materials
Pump housing	Grey cast iron
Impeller	PK-GF30
Shaft	Stainless steel
Motor housing	Stainless steel

Installation dimensions
Pipe connection on the suction side DNs	-
Pipe connection on the discharge side DNd	G 1½

DrainLift WS 50E Basic

Product data
Brand	Wilo
Product description	DrainLift WS 50E BASIC/MINI3 V04/M06-523
Article number	2552864
EAN number	4062679025490
Colour	grey/black
Minimum order quantity	1
Date of sales availability	2020-06-01

Packaging
Packaging type	Euro pallet
Packaging property	Transport packaging
Pieces per pallet	1
Number per layer	1

Dimension, weight
Length with packaging	1200 mm
Length L	800 mm
Height with packaging	1202 mm
Height H	1042 mm
Width with packaging	800 mm
Width W	650 mm
Gross weight, approx. m	81 kg
Net weight, approx. m	59 kg

Plastic chamber as single-pump system. Suitable for ground installation or building installation.

Fluid

For collection and pumping of the following in commercial areas:

Sewage containing faeces

Sewage pumping according to 12050

The pump chamber meets the requirements of EN 12050-1 with the specified pump.

Construction

Chamber

Pump chamber with optimised geometry for deposit-free operation. Chamber component with finning for high inherent stability and anti-buoyancy. The inlets are freely configurable. Two lifting eyes are integrated for attaching the lifting accessory. The upward curved pump chamber cover can be walked on and can be loaded with max. 200 kg. For the building installation, the pump chamber is equipped with a floor fixation.

Pipework

Discharge pipe with threaded connection on the pump side
Shut-off ball valve
Non-return ball valve

Pump

Submersible sewage pump for single-phase current. Surface-cooled motor with thermal motor protection (self-switching) and plug.

Level control

The level is controlled via the float switch of the pump.

Scope of delivery

Plastic chamber with installed pipework, pump and level control
- Pipework with shut-off ball valve and non-return valve
- Pump with float switch and plug
Chamber cover with gasket
HT double socket 50 mm (2 in) for evacuation connection
Inlet set with hole saw 124 mm (5 in) and gasket DN 100
Floor fixation
Installation and operating instructions

Operating Data

Approved field of application
Fluid temperature T	3 °C
Ambient temperature T	3 °C
Maximum operating pressure PN	1 bar
Max. permissible pressure in the pressure pipe P	1.5 bar

Product data
Gross volume of the tank V	255 l
Switching volume V	65 l
Operating mode (non-immersed)	S3-20%
Height H	1042 mm
Length L	800 mm
Width W	650 mm
Diagonal dimension Diagonal axis	1280 mm

Motor data
Mains connection	1~230 V, 50 Hz
Voltage tolerance	±10 %
Rated power P₂	0.6 kW
Rated speed n	2900 1/min
Rated current I_N	4.1 A
Insulation class	F
Protection class motor	IP68

Cable
Connection cable length L	5 m
Cable type	H07RN-F
Cable cross-section	3G1 mm²
Mains plug	CEE 7/7 (Schuko)

Materials
Tank	PE
Pump housing	Grey cast iron
Impeller	PK-GF30
Shaft	Stainless steel
Motor housing	Stainless steel

Installation dimensions
Pipe connection on the suction side	DN100 / DN150
Pipe connection on the discharge side	Ø63/G2½"A
Connection venting	Ø 75

Ordering information
Brand	Wilo
Product description	DrainLift WS 50E BASIC/MINI3 V04/M06-523
Net weight, approx. m	59 kg
Article number	2552864

Installation and operating instructions

Wilo-DrainLift WS 40/50 Basic

Article Number	6087354
Edition	06
Number of pages	40

PDF (6 MB)

Installation and operating instructions (digital)

DrainLift WS 40/50 Basic

Article Number	6087354
Edition	2023-07

HTML (10 MB)

Open

Certification booklet

Wilo-Drainlift WS 40/50, Wilo-DrainLift WS 40/50 Basic

Article Number	6069562
Edition	2021-07
Number of pages	72

PDF (4 MB)

Mains-independent alarm signal (5) Alarm signal for detection of flooding in rooms and buildings. The alarm signal is acoustic, optical or wireless. In addition, other consumers can be controlled directly.
Float switch MS1
Float switch MS1	Float switch MS1 with 10 m cable	2004593
Float switch MS1	Float switches for level control devices as min./max switches for fluids that are aggressive or contain faeces, floats with the fluid and switches when tilted. Because of its construction and switching point, the float switch can exhibit only a very small hysteresis. This property cannot be changed, not even the length of the cable. In order to use the float switch, a switchgear with adjustable run-on time must be used. Switching: up "ON"/down "OFF" When used in potentially explosive areas an Ex cut-off relay must be provided for the connection!
Float switch WA
Float switch WA	Float switch WA65 with 10 m cable	503211893
Float switch WA	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
DrainAlarm
DrainAlarm	DrainAlarm	2545133
DrainAlarm	Mains-independent alarm switchgear (self-charging power supply unit) for wall fixation with optical and acoustic alarm signal. Inputs: 1x digital input for the connection of one float switch Outputs: 1x potential-free changeover contact, switching capacity: 250 VAC/4 A 1x non-isolated changeover contact, switching capacity: 12 VDC/1 A Scope of delivery: Alarm switchgear with built-in battery and connected power cable with shockproof plug 2x threaded cable glands M16x1.5 Installation and operating instructions Attention: Signal transmitter is to be provided on-site. Switchgears are not protected against explosions and may only be used outside potentially explosive atmospheres. Signal transmitters within hazardous areas must be connected through an intrinsically safe electric circuit, e.g. breakdown barrier or ex-rated cut-off relay.
Signal horn
Signal horn	Signal horn 1~230 V	501459398
Signal horn	Horn with bell for wall fixation for indoor and outdoor areas. Alarm signal via electromechanical noise generation with steel diaphragm (88 dBA). Notice: The signal horn can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
Flash light
Flash light	Flash light 1~230 VAC	2551613
Flash light	Xenon flash light for wall fixation for indoor and outdoor areas. Light colour: Red, flash frequency: 0.75 Hz Notice: The signal lamp can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
Stationary dry well installation (12) The operating space is divided into two parts: a fluid collection room for the fluid and a machine room where the pump is installed. The machine room is always dry and accessible. For a correct operation of the pumps, it is necessary to know the switching volume. The switching volume is calculated as the difference between the ON and OFF switching points. The OFF-switch point must always be above the hydraulic unit, otherwise there is a risk of air being trapped, which would block the next pumping operation.
Flange connector
Flange connector	Flange connector DN 100	2511597
	Flange connectors for flexible connection (max. adjustment 130 mm) of free pipes without flanges to pipes with flanges. Incl. hose, hose clips and mounting accessories.
	Flange connector DN 150	2511598
	Flange connectors for flexible connection (max. adjustment 130 mm) of free pipes without flanges to pipes with flanges. Incl. hose, hose clips and mounting accessories.
Diaphragm hand pump
Diaphragm hand pump	Diaphragm hand pump	2060166
Diaphragm hand pump	Diaphragm hand pump for manual draining of a collection reservoir. Fixed installation and mobile application possible. The pumped-off fluid must flow directly to the discharge pipe or another collection point.
Sump length extension
Sump length extension	Pump chamber extension WS 40/50	2525190
Sump length extension	Screwable pump chamber extension, incl. gasket and installation accessories. Installation note: Only one extension can be installed per pump chamber!
Clamp bolting
Clamp bolting	Clamp connection G1½"/ 50 mm	2505044
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G1½"/63 mm	2505045
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G2"/63 mm	2505046
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G2"/75 mm	2525181
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
Inlet seal
Inlet seal	DN 100 inlet seal kit	2521841
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 110 mm Hose clip Hole saw
	DN 150 inlet seal kit	2515145
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 160 mm Hose clip Hole saw
Shut-off device for wastewater and sewage
Shut-off device for wastewater and sewage	Gate valve G 1½, CW617N	2525187
Shut-off device for wastewater and sewage	Gate valve in bushing version with female thread and handwheel for shutting off the pipe network.
3-way cock
3-way cock	3-way shut-off ball cock Rp 1½	2511607
3-way cock	Shut-off ball cock for switching between 2 circuits: With T drill-hole 3 connections as female thread Handle Ball sealed on all sides.

Fittings (2)
3-way cock
3-way cock	3-way shut-off ball cock Rp 1½	2511607
3-way cock	Shut-off ball cock for switching between 2 circuits: With T drill-hole 3 connections as female thread Handle Ball sealed on all sides.
Shut-off device for wastewater and sewage
Shut-off device for wastewater and sewage	Gate valve G 1½, CW617N	2525187
Shut-off device for wastewater and sewage	Gate valve in bushing version with female thread and handwheel for shutting off the pipe network.
Installation/setup (21)
Clamp bolting
Clamp bolting	Clamp connection G1½"/ 50 mm	2505044
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G1½"/63 mm	2505045
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G2"/63 mm	2505046
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G2"/75 mm	2525181
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection 50mm/50 mm	2525183
	Clamp bolting for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection 50mm/63 mm	2525184
	Clamp bolting for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G1¼"/40 mm	2543025
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G1¼"/50 mm	2543026
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
	Clamp connection G1¼"/63 mm	2543027
	Clamp bolting with female thread for connection to a PE discharge pipe outside the pump chamber.
Diaphragm hand pump
Diaphragm hand pump	Diaphragm hand pump	2060166
Diaphragm hand pump	Diaphragm hand pump for manual draining of a collection reservoir. Fixed installation and mobile application possible. The pumped-off fluid must flow directly to the discharge pipe or another collection point.
Inlet seal
Inlet seal	Inlet seal DN 32	6096498
	Lip seal for sealing inlets with a pipe diameter of 40 mm.
	DN 40 inlet seal	6096499
	Lip seal for sealing inlets with a pipe diameter of 50 mm.
	DN 100 inlet seal	2522672
	Lip seal for sealing inlets with a pipe diameter of 110 mm.
	DN 150 inlet seal	2552849
	Lip seal for sealing inlets with a pipe diameter of 160 mm.
	DN 200 inlet seal	2552850
	Lip seal for sealing inlets with a pipe diameter of 225 mm.
	DN 32 inlet seal kit	6096492
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 40 mm Hose clip Hole saw
	DN 40 inlet seal kit	6096493
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 50 mm Hose clip Hole saw
	DN 100 inlet seal kit	2521841
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 110 mm Hose clip Hole saw
	DN 150 inlet seal kit	2515145
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 160 mm Hose clip Hole saw
	DN 200 inlet seal kit	2552851
	Inlet kit for sealing inlets, consisting of: Lip seal for pipe diameter of 225 mm Hose clip Hole saw
Sump length extension
Sump length extension	Pump chamber extension WS 40/50	2525190
Sump length extension	Screwable pump chamber extension, incl. gasket and installation accessories. Installation note: Only one extension can be installed per pump chamber!
Pipes/pipe joints (2)
Flange connector
Flange connector	Flange connector DN 100	2511597
	Flange connectors for flexible connection (max. adjustment 130 mm) of free pipes without flanges to pipes with flanges. Incl. hose, hose clips and mounting accessories.
	Flange connector DN 150	2511598
	Flange connectors for flexible connection (max. adjustment 130 mm) of free pipes without flanges to pipes with flanges. Incl. hose, hose clips and mounting accessories.

Alarm signal (7)
DrainAlarm
DrainAlarm	DrainAlarm	2545133
	Mains-independent alarm switchgear (self-charging power supply unit) for wall fixation with optical and acoustic alarm signal. Inputs: 1x digital input for the connection of one float switch Outputs: 1x potential-free changeover contact, switching capacity: 250 VAC/4 A 1x non-isolated changeover contact, switching capacity: 12 VDC/1 A Scope of delivery: Alarm switchgear with built-in battery and connected power cable with shockproof plug 2x threaded cable glands M16x1.5 Installation and operating instructions Attention: Signal transmitter is to be provided on-site. Switchgears are not protected against explosions and may only be used outside potentially explosive atmospheres. Signal transmitters within hazardous areas must be connected through an intrinsically safe electric circuit, e.g. breakdown barrier or ex-rated cut-off relay.
	DrainAlarm FIRST	2550526
	Alarm switchgear for wall fixation with optical and acoustic alarm signal. Inputs: 1x digital input for the connection of one float switch Outputs: 1x potential-free changeover contact, switching capacity: 250 VAC/4 A 1x non-isolated changeover contact, switching capacity: 12 VDC/1 A Scope of delivery: Alarm switchgear with connected power cable and shockproof plug 2x threaded cable glands M16x1.5 Installation and operating instructions Attention: Signal transmitter is to be provided on-site. Switchgears are not protected against explosions and may only be used outside potentially explosive atmospheres. Signal transmitters within hazardous areas must be connected through an intrinsically safe electric circuit, e.g. breakdown barrier or ex-rated cut-off relay.
Flash light
Flash light	Mounted Flash light 1~230 VAC	2510429
	Xenon flash light for indoor and outdoor areas for installing on the switch cabinet. Light colour: Red, flash frequency: 0.75 Hz Notice: The signal lamp can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
	Flash light 24 VDC	2551612
	Xenon flash light for wall fixation for indoor and outdoor areas. Light colour: Red, flash frequency: 0.75 Hz Notice: The signal lamp can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
	Flash light 1~230 VAC	2551613
	Xenon flash light for wall fixation for indoor and outdoor areas. Light colour: Red, flash frequency: 0.75 Hz Notice: The signal lamp can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
Signal horn
Signal horn	Signal horn 12-24 VDC	2017208
	Horn with bell for wall fixation for indoor and outdoor areas. Alarm signal via electromechanical noise generation with steel diaphragm (92 dBA). Notice: The signal horn can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
	Signal horn 1~230 V	501459398
	Horn with bell for wall fixation for indoor and outdoor areas. Alarm signal via electromechanical noise generation with steel diaphragm (88 dBA). Notice: The signal horn can be connected to a potential-free contact (SSM/ESM) on the switchgear. The power supply must be provided by the customer!
Level control (10)
Float switch MS1
Float switch MS1	Float switch MS1 with 10 m cable	2004593
Float switch MS1	Float switches for level control devices as min./max switches for fluids that are aggressive or contain faeces, floats with the fluid and switches when tilted. Because of its construction and switching point, the float switch can exhibit only a very small hysteresis. This property cannot be changed, not even the length of the cable. In order to use the float switch, a switchgear with adjustable run-on time must be used. Switching: up "ON"/down "OFF" When used in potentially explosive areas an Ex cut-off relay must be provided for the connection!
Float switch WA
Float switch WA	Float switch WA65 with 5 m cable	503211390
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 10 m cable	503211893
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 20 m cable	2004431
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 with 30 m cable	2004432
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA KR1 S with 5 m cable	6082806
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA KR1 S with 10 m cable	6082807
	As a signal transmitter for the system switching, depending on the level of an open container or a cistern. Switching points: up ON / down OFF
	Float switch WA65 (PSN-X) with 20 m cable	6088843
	As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC
	Float switch WA65 (PSN-X) with 10 m cable	6088844
	As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC
	Float switch WA65 (PSN-X) with 5 m cable	6088845
	As a signal transmitter for the system switching, depending on the fill level of an open tank or a cistern. Switching points: up ON/down OFF with switching contacts NO/COM/NC

With Wilo as your partner, you can not only be sure of choosing high-quality product solutions, but also of benefiting from a comprehensive, worry-free package of well thought-out services. We collaborate to develop a service concept tailored to your individual needs; with our expertise and personal consultancy, we make sure that the operation of your systems is as energy-efficient, reliable and economical as possible. All the while our competent Wilo service technicians are ready to assist you with fast, reliable and on-time support.

Recommended services
Commissioning	Commissioning Pump stations	2219492
	For perfect functioning of the pump(s) / system(s), it is recommended to have the commissioning carried out by the works' own WILO SE Customer Service Department. Optimum setting and efficient operation of the system are ensured as a result. Commissioning is comprised of the following points: Commissioning of system(s) according to checklist Parameterisation and setting of switchgear Testing and adaptation of initial compressing of pressure tanks (filling up to 80 litres incl.) Functional check of fitted system(s) Practice-oriented operation instruction Wilo commissioning protocol The price for commissioning only applies to system(s) which have been installed in accordance with the installation and operating instructions and state-of-the-art technology. No costs for any materials which may be required are included.
Maintenance	Maintenance BASIC Pump stations	2219544
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance COMFORT Pump stations	2219519
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during normal service hours) Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance PREMIUM Pump stations	2219572
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Checking the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during and outside normal service hours) Software updates Includes wearing parts Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
Supervision	Supervision Pump stations	2219353
	Wilo supports during the concept phase to ensure quality work and cost efficiency. Our competent and qualified Wilo Service will support you with recommendations and technical advice throughout the entire project. Supervision includes: Regular on-site visits ensure the quality of information and advice Technical consultancy, also available on site Status report with recommendations after the visit Comprehensive support from a Wilo expert
More suitable services
Service packages	Service Package L Pump stations	2219724
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package L includes: Installation check Supervision Commissioning Maintenance Energy Solutions WiloCare Premium Wilo-Live Assistant Optional add-on services: System Optimisation Repairs Extended Warranty
	Service Package M Pump stations	2219695
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package M includes: Installation check Supervision Commissioning Maintenance WiloCare Comfort Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Repairs Extended Warranty
	Service Package S Pump stations	2219666
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package S includes: Installation check Commissioning Maintenance WiloCare Basic Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Supervision Repairs Extended Warranty
Wilo-Live Assistant	Wilo-Live Assistant Service	2216415
	The Wilo-Live Assistant is a technical advisor at your side during pump service. By using the Wilo-Live Assistant, our expert advisers can support you in the boiler or equipment room via video transmission – live and in real time. You use your smartphone to show the installation set-up, while the Wilo expert follows everything on their screen. They can see the components as well as other details and can thus determine where the fault or breakdown originates. We prevent downtime and ensure operational reliability of your pumps and systems! The Wilo-Live Assistant includes: Interactive live support via video chat Direct contact with an expert Just-in-time solution to ensure maximum operational reliability of your pumps and systems
Extended Warranty	Extended Warranty Pump stations	2219470
	In combination of a new pump or system Wilo offers an extended warranty of up to five years in combination with commissioning and maintenance by the Wilo Service. Extended warranty includes: Full protection and predictable cost security Regular maintenance work by the Wilo Service
Installation	Installation Pump stations	2219388
	The Wilo service offers installation of our pumps or pumping systems. We offer an end-to-end process from gathering information on site to installing our product in the overall plant. An optimal installation set-up and the interaction of various individual factors lay the foundation for long-term operational safety. Installation includes: Professional inspection Provision of components/materials from Wilo and third-party suppliers Installation of pipelines and electronics Test runs
System Optimisation	System Optimisation Pump stations	2219283
	The Wilo Service offers proactive system optimisation by optimising settings and doing minor adjustments to ensure operational reliability. System Optimisation includes among others: Overhaul of pumps/systems to restore full performance Addition of new technologies or functions in older systems to save on capital expenditures (retrofitting)
Energy Solutions	Energy Solutions Pump stations	2219318
	Wilo Service offers a proactive support to point out possible energy savings. Our service creates an overview of all installed assets to show how the energy consumption of pumps or systems can be reduced. We offer targeted consultancy and analysis, including the involvement of subsidies as well as comprehensive support around the changeover to high-efficiency technologies. Wilo-Energy solution includes: Detailed assessment of the life cycle costs (LCC analysis) Energy audit including information about energy saving potential Proactive recommendation of replacement options Improving the environmental performance of your system Support in the changeover to Wilo high-efficiency pumps
Repair	Repair Pump stations	2219637
	Wilo Service draws on their competence and experience while consulting on site to decide whether the pump can actually be repaired on site or has to be sent in for a factory repair. Wilo also provides spare parts or a replacement pump to restore the operational reliability of the system. Repair includes: Verification and elimination of error causes by experienced Wilo experts Non-binding estimate for repairs Electric-hydraulic test run to ensure correct data regarding functionality, quality and performance of the pump or system Coating of various pump or system components for an optimised efficiency factor Use of genuine spare parts only Documentation of the repair in the service report

DrainLift WS 50E BASIC/MINI3 V04/M06-523

DrainLift WS 50E Basic

Installation and operating instructions

Wilo-DrainLift WS 40/50 Basic

Installation and operating instructions (digital)

DrainLift WS 40/50 Basic

Certification booklet

Wilo-Drainlift WS 40/50, Wilo-DrainLift WS 40/50 Basic

Mains-independent alarm signal (5)

Float switch MS1

Float switch MS1

Float switch WA

Float switch WA

DrainAlarm

DrainAlarm

Signal horn

Signal horn

Flash light

Flash light

Stationary dry well installation (12)

Flange connector

Flange connector

Diaphragm hand pump

Diaphragm hand pump

Sump length extension

Sump length extension

Clamp bolting

Clamp bolting

Inlet seal

Inlet seal

Shut-off device for wastewater and sewage

Shut-off device for wastewater and sewage

3-way cock

3-way cock

Fittings (2)

3-way cock

3-way cock

Shut-off device for wastewater and sewage

Shut-off device for wastewater and sewage

Installation/setup (21)

Clamp bolting

Clamp bolting

Diaphragm hand pump

Diaphragm hand pump

Inlet seal

Inlet seal

Sump length extension

Sump length extension

Pipes/pipe joints (2)

Flange connector

Flange connector

Alarm signal (7)

DrainAlarm

DrainAlarm

Flash light

Flash light

Signal horn

Signal horn

Level control (10)

Float switch MS1

Float switch MS1

Float switch WA

Float switch WA

Recommended services

Commissioning

Maintenance

Supervision

More suitable services

Service packages

Wilo-Live Assistant

Extended Warranty

Installation

System Optimisation

Energy Solutions

Repair