Stratos GIGA2.0-I 32/1-13/0,55-S1 | Wilo

Stratos GIGA2.0-I 32/1-13/0,55-S1

Article number: 2204785

Hydraulic data
Minimum efficiency index (MEI)	≥0.7
Maximum operating pressure PN	16 bar
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Min. ambient temperature T_min	0 °C
Max. ambient temperature T_max	50 °C

Drive
Mains connection	3~400 V, 50/60 Hz
Number of poles	4
Motor efficiency class	IE5
Power consumption P_{1 max}	0.70 kW
Rated power P₂	0.55 kW
Max current I_max	1.1 A
Emitted interference	EN 61800-3
Interference resistance	EN 61800-3
Insulation class	F
Protection class motor	IP55
Motor protection	PTC integrated

Materials
Pump housing	Grey cast iron
Impeller	PPS-GF40
Shaft	Stainless steel
Shaft seal	Q1Q1X4GG
Lantern	5.1301/EN-GJL-250 KTL-coated

Approved liquids (other liquids upon request)
Heating water (as per VDI 2035)	yes
Heat carrier oil	Special version at additional charge
Cooling and cold water circulation systems	yes
Water-glycol mixtures (at 20 – 40 vol. % glycol and fluid temperature ≤ 40 °C)	yes

Installation dimensions
Port-to-port length L0	260 mm
Pipe connection on the suction side DNs	DN 32
Pipe connection on the discharge side DNd	DN 32

Stratos GIGA2.0-I 32/1-13/0,55-S1

Wilo-Stratos GIGA2.0

Bezeichnung

Product data
Brand	Wilo
Product description	Stratos GIGA2.0-I 32/1-13/0,55-S1
Article number	2204785
EAN number	4062679106984
Colour	Green/black/grey
Minimum order quantity	1
Date of sales availability	2022-08-15

Packaging
Packaging type	Cardboard box
Packaging property	Transport packaging
Pieces per pallet	1
Number per layer	2

Dimension, weight
Length with packaging	800 mm
Length L	595 mm
Height with packaging	525 mm
Height H	370 mm
Width with packaging	600 mm
Width W	248 mm
Gross weight, approx. m	41 kg
Net weight, approx. m	32 kg

High-efficiency in-line pump with EC motor of energy efficiency class IE5 in accordance with IEC 60034-30-2, hydraulics with minimum efficiency index MEI ≥ 0.7 and electronic power adjustment with a glanded pump design. The pump is configured as a single-stage low-pressure centrifugal pump with flange connection and mechanical seal. The Stratos GIGA2.0-I has been predominantly designed for pumping heating water (acc. to VDI 2035), chilled water and water-glycol mixtures without abrasive substances in heating, air-conditioning and cooling systems.

Design ...-S1:

Single-stage low-pressure centrifugal pump with one-piece shaft in monobloc design
Spiral housing in in-line design (suction and discharge ports with the same flanges in a line)
PN 16 flange – in accordance with EN 1092-2
Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor)
Pump housing and motor flange with cataphoretic coating as standard
Mechanical seal S1 recommended for water-glycol mixtures with glycol proportions up to max. 50% by volume and a fluid temperature of -20 °C up to max. +90 °C – +110 °C and also if there is oil in the water-glycol mixture.
Connection voltages:
- 3~440 V ±10% 50/60 Hz; 3~400 V ±10% 50/60 Hz; 3~380 V -5% +10% 50/60 Hz
- Version M-: 1~220 V – 240 V (±10%), 50/60 Hz
Compliance with electromagnetic compatibility without additional measures
- Interference emission for residential environment according to EN 61800-3:2018
- Interference immunity for industrial environments according to EN 61800-3:2018

Control modes:

Permanent, automatic power adjustment to system requirements without setpoint specification Wilo Dynamic Adapt plus (factory setting).
Constant temperature (T-const.)
Constant differential temperature (dT-const.)
Needs-based volume flow optimisation of the feeder pump through connectivity and communication between multiple secondary pumps (Multi-Flow Adaptation).
Constant volume flow (Q-const.)
Variable differential pressure (dp-v) with the option to set the nominal duty point Q and H
Constant differential pressure (dp-c)
Differential pressure control (dp-c) to a remote point in the pipe network (index circuit evaluator)
Constant speed (n-const.)
User-defined PID control

Functions:

Selection of the field of application in the setting assistant
Heat quantity measurement
Cooling quantity measurement
Adjustable volume flow limiter using the Q-Limit function (Q_min. and Q_max.)
Operating modes of twin-head pump: Main/standby operation, efficiency-optimised parallel operation for dp-c and dp-v
Pump automatically deactivates when no flow is detected (No-Flow Stop)
Switchover between heating and cooling mode (automatic, external or manual)
Ability to save and restore configured pump settings (3 restoration points)
Display of current duty point in the hydraulic duty chart
Correction of viscous fluids via adjustment of viscosity and density
Fault and warning messages shown in plain text with advice on resolving the issue
Integrated full motor protection

Display in the "Home screen" of the graphic display:

Control mode currently set
Current setpoint
Current volume flow (only if a differential pressure sensor is connected)
Current fluid temperature (only if temperature sensor is connected)
Current power consumption
Cumulative electric consumption

Version:

4 configurable analogue inputs: 0-10 V, 2-10 V, 0-20 mA, 4-20 mA and commercially available PT1000 (only on two analogue inputs); +24 V DC power supply
2 configurable digital inputs (Ext. OFF, Ext. Min, Ext. Max, heating/cooling, manual override (uncoupled from building automation), operation lock (key lock and remote operation configuration protection))
2 configurable signal relays for run signals and fault messages
Slot for Wilo-CIF modules with interfaces for building automation (BA) (optional accessories: CIF modules Modbus RTU, BACnet MS/TP, LON, PLR, CAN)
Wilo Net as a Wilo system bus for communication between Wilo products, e.g. Multi-Flow Adaptation; dual-pump operation
Automatic emergency operation with definable pump speed for exceptional circumstances, e.g. bus communication or sensor value malfunction
Rotatable, graphic colour display (4.3 inches) with one button manual operation level
Bluetooth interface via Wilo-Smart Connect module BT
Use the Wilo-Assistant app to read and set operating data and –among other things– set up a commissioning protocol through the Bluetooth interface
Integrated dual-pump management (twin-head pumps are prewired) when using 2 single pumps as two-pump unit (connection via Wilo Net)
Cable break detection when using an analogue signal (in connection with 2 – 10 V or 4 – 20 mA)
Time stamp for error/warnings and historical operating data
Continuous operating data memory
Standard condensate drainage holes in the motor housing (closed upon delivery)
Air vent valve on the lantern

Scope of delivery:

Pump
Wilo-Smart Connect module BT
Threaded cable glands with sealing inserts
Installation and operating instructions and declaration of conformity

Accessories must be ordered separately:

3 mounting brackets with fixation material for installation on a base

Blind flanges for twin-head pump housing
Installation aid for mechanical seal (incl. mounting bolts)
For connection to building automation:
- CIF module PLR
- CIF module LON
- CIF module BACnet MS/TP
- CIF module Modbus RTU
- CIF module CANopen
- CIF module Ethernet Multi-protocol (Modbus TCP, BACnet/IP)
- Connection M12 RJ45 CIF Ethernet
Differential pressure sensor DDG 2 – 10 V
Differential pressure sensor DDG 4 – 20 mA
Temperature sensor PT1000 AA
Sensor sleeves for the installation of temperature sensors in the pipe

Operating Data
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Min. ambient temperature T_min	0 °C
Max. ambient temperature T_max	50 °C
Maximum operating pressure PN	16 bar
Minimum efficiency index (MEI)	≥0.7

Drive
Mains connection	3~400 V, 50/60 Hz
Motor efficiency class	IE5
Power consumption P_{1 max}	700 W
Rated power P₂	0.55 kW
Max current I_max	1.1 A
Max. speed n_max	2600 1/min
Emitted interference	EN 61800-3
Interference resistance	EN 61800-3
Insulation class	F
Protection class motor	IP55
Motor protection	PTC integrated

Materials
Pump housing	Grey cast iron
Impeller	PPS-GF40
Shaft	Stainless steel
Shaft seal	Q1Q1X4GG
Lantern	5.1301/EN-GJL-250 KTL-coated

Installation dimensions
Pipe connection on the suction side DNs	DN 32
Pipe connection on the discharge side DNd	DN 32
Port-to-port length L0	260 mm

Ordering information
Brand	Wilo
Product description	Stratos GIGA2.0-I 32/1-13/0,55-S1
Net weight, approx. m	32 kg
Article number	2204785

Installation and operating instructions

Wilo-Stratos GIGA2.0-I/-D

Article Number	2227296
Edition	2023-08
Number of pages	488
Language	de, en, fr, nl

PDF (13 MB)

Certification booklet

Wilo-Stratos GIGA2.0-I/-D, Wilo-Stratos GIGA /-D/-B, Wilo-Yonos GIGA2.0-I/-D

Article Number	2216678
Edition	2022-11
Number of pages	52
Language	language neutral

PDF (22 MB)

Group Statement

Group Statement REACH

Edition	2021-05
Number of pages	5
Language	language neutral

PDF (327 KB)

UN38.3

Lithium Battery UN38.3 Test UN38.3-187

Number of pages	6
Language	language neutral

PDF (517 KB)

Continuous, infinitely variable control, differential pressure-sensitive CCe-HVAC system (26)
CCe-HVAC system
CCe-HVAC system	CCe-HVAC system 1 x 0.37	2536646
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 2 x 0.37	2536647
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 3 x 0.37	2536648
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 4 x 0.37	2536649
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 5 x 0.37	2536650
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 6 x 0.37	2536651
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module CC
Communication module CC	CC communication module	2533850
Communication module CC	Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery Communication module CC Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
Extension kit differential pressure sensor for Y-piece application
Extension kit differential pressure sensor for Y-piece application	Extension for DDG-kit	2166098
	Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection: 1 x Double nipple M3 1 x Double nipple M5 1 x Nut with clamp ring 1 x Nut M8x1 D.5 1 x Reduced clamp ring 1 x Copper spiral Ø 3 mm, length max. 2 m Pipework connection: 1 x Clamping ring screw connectionR¹/8 PASSAGE 1 x Clamping ring screw connectionR¹/8 CORNER (90°) 1 x Screw R¹/8 DIN906 8.8 ST 1 supplementary sheet (installation instructions) Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications
Continuous, infinitely variable control, temperature-dependent CCe-HVAC system (24)
CCe-HVAC system
CCe-HVAC system	CCe-HVAC system 1 x 0.37	2536646
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 2 x 0.37	2536647
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 3 x 0.37	2536648
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 4 x 0.37	2536649
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 5 x 0.37	2536650
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 6 x 0.37	2536651
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module CC
Communication module CC	CC communication module	2533850
Communication module CC	Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery Communication module CC Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
Continuous, infinitely variable control, differential pressure-sensitive SCe-HVAC system (18)
SCe-HVAC system
SCe-HVAC system	SCe-HVAC system 1x10A-WM	2545254
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 2x10A-WM	2545255
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 3x10A-WM	2545256
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 4x10A-WM	2545257
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
Extension kit differential pressure sensor for Y-piece application
Extension kit differential pressure sensor for Y-piece application	Extension for DDG-kit	2166098
	Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection: 1 x Double nipple M3 1 x Double nipple M5 1 x Nut with clamp ring 1 x Nut M8x1 D.5 1 x Reduced clamp ring 1 x Copper spiral Ø 3 mm, length max. 2 m Pipework connection: 1 x Clamping ring screw connectionR¹/8 PASSAGE 1 x Clamping ring screw connectionR¹/8 CORNER (90°) 1 x Screw R¹/8 DIN906 8.8 ST 1 supplementary sheet (installation instructions) Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications
Continuous, infinitely variable control, temperature-dependent SCe-HVAC system (14)
SCe-HVAC system
SCe-HVAC system	SCe-HVAC system 1x10A-WM	2545254
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 2x10A-WM	2545255
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 3x10A-WM	2545256
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 4x10A-WM	2545257
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw

Wall fixation/installation on a base (1)
Mounting bracket kit
Mounting bracket kit	Mounting bracket F 3-14 SET	2040968
Mounting bracket kit	Mounting brackets for the installation on a base of in-line and monobloc pumps. Comprised of several angle brackets (number dependent on the pump type), intended for the screwed connection with the screw-on bases or feet of the pump. The angle brackets ensure secure fastening of the pump to the foundation. Including fixation material. Notice The mounting brackets / angle brackets must be lined by the dimension specified for the following pump types: BL 65/270-5.5/4, BL 80/250-5.5/4, BL/BL-E 80/250-7.5/4: 30 mm all types BL 100/..., BL 125/220..., BL/BL-E 125/260..., BL/BL-E 125/270...: 20 mm all types BL 125/190..., BL 125/200..., BL 125/250...: 40 mm Scope of delivery Screws Angle brackets Screw stays Nuts

Pump control/accessories (28)
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	SMA/FME adapter	2545548
	Koaxialer Steckverbinder SMA-Stecker auf FME-Stecker in kompakten Bauform mit Schraubverschluss. Einsetzbar bis 2 GHz, der Wellenwiderstand beträgt 50 Ω.
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
Communication module CC
Communication module CC	CC communication module	2533850
Communication module CC	Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery Communication module CC Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Immersion sleeve
Immersion sleeve	Immersion sleeve G ½, 45mm	2193423
	Immersion sleeve with PG 7 clamp bolting and silicone rings. For admission of the immersion sensor Pt 1000 AA for connection to Stratos MAXO. Thread: G 1/2 Inner Ø 6.4 mm for sensor to Ø 6 mm Length of engagement 45 mm for installation in thread T-connector for use with pipes from DN 25 to approx. DN 50
	Immersion sleeve G ½, 100mm	2193424
	Immersion sleeve with PG 7 clamp bolting and silicone rings. For admission of the immersion sensor Pt 1000 AA for connection to Stratos MAXO. Thread: G 1/2 Inner Ø 6.4 mm for sensor to Ø 6 mm Length of engagement 100 mm for installation in thread T-connector for use with pipes from approx. DN 65 to DN 100
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
	BACnet IP SC communication module	2553366
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe booster with BACnet IP networks. The communication module SC-OPTION BACnet IP is a hardware extension and optionally a software extension to connect an SC/SCe system as a participant in an existing BACnet IP building automation. The connection of the BACnet IP module to the RS485 bus takes place via twisted-pair cabling. BACnet (Building Automation and Control Networks) IP ensures interoperability between devices from different manufacturers. With BACnet IP, different parameters can be read and written, e.g. switchgear data, pump status and modes, actual values, setpoints, the current speed of the pump, measured temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Only Wilo customer service can perform a subsequent activation and installation of the BACnet IP function in the switchgear. Scope of delivery BACnet IP module Fixation material Connecting cable Activation code Installation and operating instructions
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Temperature sensor Pt 1000
Temperature sensor Pt 1000	Immersion temperature sensor Pt 1000 AA	2193422
Temperature sensor Pt 1000	Temperature sensor for installation in immersion sleeve with inside diameter 6.5 mm. Connection to Stratos MAXO and Stratos GIGA2.0 to detect the fluid temperature in the case of temperature-dependent pump control or to detect heating/cooling quantities. Sensor Pt 1000 Class AA, Ø 6 x 40 mm Cable length: 3 m Measurement range: -5 °C to 70 °C, briefly up to 90 °C
Pump control/Comfort control system (6)
CCe-HVAC system
CCe-HVAC system	CCe-HVAC system 1 x 0.37	2536646
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 2 x 0.37	2536647
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 3 x 0.37	2536648
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 4 x 0.37	2536649
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 5 x 0.37	2536650
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CCe-HVAC system 6 x 0.37	2536651
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server. For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Pump control/Smart control system (4)
SCe-HVAC system
SCe-HVAC system	SCe-HVAC system 1x10A-WM	2545254
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 2x10A-WM	2545255
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 3x10A-WM	2545256
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SCe-HVAC system 4x10A-WM	2545257
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC - Emission standard for residential, commercial and light-industrial environments EN 61000-6-3 (for SC-FC only up to 9.0 kW, above this: EN 61000-6-4 Emission standard for industrial environments) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller) Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Pump control/interface module (6)
CIF-Modules
CIF-Modules	CIF-Module BACnet MS/TP	2190367
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. General functions Serial, digital interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment RS485 interface with BACnet MS/TP protocol Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 2x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) Installation and operating instructions Bus lines (shielded!) must be provided by the customer
	CIF-Module Modbus RTU	2190368
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. General functions Serial, digital interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment RS485 interface with Modbus RTU protocol Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 2x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) Installation and operating instructions Bus lines (shielded!) must be provided by the customer
	CIF-Module CANopen	2190369
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. General functions Serial, digital interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment CAN 2.0A interface with CANopen protocol Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 2x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) Installation and operating instructions Bus lines (shielded!) must be provided by the customer
	CIF-Module LON	2190370
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. General functions Serial, digital interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment TP-FT 10 interface with LonTalk protocol Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 2x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) Installation and operating instructions Bus lines (shielded!) must be provided by the customer
	CIF-Module PLR	2190371
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. General functions Serial, digital interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment PLR interface (WILO) Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 1x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) Installation and operating instructions Bus lines (shielded!) must be provided by the customer
	CIF-Module Ethernet	2211408
	Interface module as retrofittable plug-in module for extending the communication interfaces of the pump by an Ethernet network connection. BACnet IP and Modbus TCP protocols can be selected in the configuration. General functions Network interface for connection to building automation for the transfer of data points as: Control commands to the pump Messages from the pump Process values Equipment Ethernet interface with Modbus TCP and BACnet IP protocol Information about the download http://www.wilo.de/automation (German) http://www.wilo.com/automation (English) Scope of delivery CIF module 2x M16x1.5 threaded cable glands (only suitable for Stratos MAXO) 2x RJ45 plugs that can be attached in the field Installation and operating instructions Network cable (shielded!) must be provided by the customer
Differential pressure detection (3)
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
Extension kit differential pressure sensor for Y-piece application
Extension kit differential pressure sensor for Y-piece application	Extension for DDG-kit	2166098
	Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection: 1 x Double nipple M3 1 x Double nipple M5 1 x Nut with clamp ring 1 x Nut M8x1 D.5 1 x Reduced clamp ring 1 x Copper spiral Ø 3 mm, length max. 2 m Pipework connection: 1 x Clamping ring screw connectionR¹/8 PASSAGE 1 x Clamping ring screw connectionR¹/8 CORNER (90°) 1 x Screw R¹/8 DIN906 8.8 ST 1 supplementary sheet (installation instructions) Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications

With Wilo as your partner, you can not only be sure of choosing high-quality product solutions, but also of benefiting from a comprehensive, worry-free package of well thought-out services. We collaborate to develop a service concept tailored to your individual needs; with our expertise and personal consultancy, we make sure that the operation of your systems is as energy-efficient, reliable and economical as possible. All the while our competent Wilo service technicians are ready to assist you with fast, reliable and on-time support.

Recommended services
Wilo-Live Assistant	Wilo-Live Assistant Service	2216415
	The Wilo-Live Assistant is a technical advisor at your side during pump service. By using the Wilo-Live Assistant, our expert advisers can support you in the boiler or equipment room via video transmission – live and in real time. You use your smartphone to show the installation set-up, while the Wilo expert follows everything on their screen. They can see the components as well as other details and can thus determine where the fault or breakdown originates. We prevent downtime and ensure operational reliability of your pumps and systems! The Wilo-Live Assistant includes: Interactive live support via video chat Direct contact with an expert Just-in-time solution to ensure maximum operational reliability of your pumps and systems
Supervision	Supervision Glanded pumps	2219321
	Wilo supports during the concept phase to ensure quality work and cost efficiency. Our competent and qualified Wilo Service will support you with recommendations and technical advice throughout the entire project. Supervision includes: Regular on-site visits ensure the quality of information and advice Technical consultancy, also available on site Status report with recommendations after the visit Comprehensive support from a Wilo expert
Commissioning	Commissioning Glanded pumps	2219391
	For perfect functioning of the pump(s) / system(s), it is recommended to have the commissioning carried out by the works' own WILO SE Customer Service Department. Optimum setting and efficient operation of the system are ensured as a result. Commissioning is comprised of the following points: Commissioning of system(s) according to checklist Parameterisation and setting of switchgear Testing and adaptation of initial compressing of pressure tanks (filling up to 80 litres incl.) Functional check of fitted system(s) Practice-oriented operation instruction Wilo commissioning protocol The price for commissioning only applies to system(s) which have been installed in accordance with the installation and operating instructions and state-of-the-art technology. No costs for any materials which may be required are included.
Maintenance	Maintenance BASIC Glanded pumps	2219531
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance COMFORT Glanded pumps	2219493
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during normal service hours) Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
	Maintenance PREMIUM Glanded pumps	2219546
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Checking the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during and outside normal service hours) Software updates Includes wearing parts Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request.
More suitable services
Service packages	Service Package L Glanded pumps	2219697
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package L includes: Installation check Supervision Commissioning Maintenance Energy Solutions WiloCare Premium Wilo-Live Assistant Optional add-on services: System Optimisation Repairs Extended Warranty
	Service Package M Glanded pumps	2219668
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package M includes: Installation check Supervision Commissioning Maintenance WiloCare Comfort Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Repairs Extended Warranty
	Service Package S Glanded pumps	2219639
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package S includes: Installation check Commissioning Maintenance WiloCare Basic Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Supervision Repairs Extended Warranty
Extended Warranty	Extended Warranty Glanded pumps	2219590
	In combination of a new pump or system Wilo offers an extended warranty of up to five years in combination with commissioning and maintenance by the Wilo Service. Extended warranty includes: Full protection and predictable cost security Regular maintenance work by the Wilo Service
Installation	Installation Glanded pumps	2219356
	The Wilo service offers installation of our pumps or pumping systems. We offer an end-to-end process from gathering information on site to installing our product in the overall plant. An optimal installation set-up and the interaction of various individual factors lay the foundation for long-term operational safety. Installation includes: Professional inspection Provision of components/materials from Wilo and third-party suppliers Installation of pipelines and electronics Test runs
System Optimisation	System Optimisation Glanded pumps	2219251
	The Wilo Service offers proactive system optimisation by optimising settings and doing minor adjustments to ensure operational reliability. System Optimisation includes among others: Overhaul of pumps/systems to restore full performance Addition of new technologies or functions in older systems to save on capital expenditures (retrofitting)
Energy Solutions	Energy Solutions Glanded pumps	2219240
	Wilo Service offers a proactive support to point out possible energy savings. Our service creates an overview of all installed assets to show how the energy consumption of pumps or systems can be reduced. We offer targeted consultancy and analysis, including the involvement of subsidies as well as comprehensive support around the changeover to high-efficiency technologies. Wilo-Energy solution includes: Detailed assessment of the life cycle costs (LCC analysis) Energy audit including information about energy saving potential Proactive recommendation of replacement options Improving the environmental performance of your system Support in the changeover to Wilo high-efficiency pumps
Repair	Repair Glanded pumps	2219610
	Wilo Service draws on their competence and experience while consulting on site to decide whether the pump can actually be repaired on site or has to be sent in for a factory repair. Wilo also provides spare parts or a replacement pump to restore the operational reliability of the system. Repair includes: Verification and elimination of error causes by experienced Wilo experts Non-binding estimate for repairs Electric-hydraulic test run to ensure correct data regarding functionality, quality and performance of the pump or system Coating of various pump or system components for an optimised efficiency factor Use of genuine spare parts only Documentation of the repair in the service report

Stratos GIGA2.0-I 32/1-13/0,55-S1

Stratos GIGA2.0-I 32/1-13/0,55-S1

Wilo-Stratos GIGA2.0

Installation and operating instructions

Wilo-Stratos GIGA2.0-I/-D

Certification booklet

Wilo-Stratos GIGA2.0-I/-D, Wilo-Stratos GIGA /-D/-B, Wilo-Yonos GIGA2.0-I/-D

Group Statement

Group Statement REACH

UN38.3

Lithium Battery UN38.3 Test UN38.3-187

Continuous, infinitely variable control, differential pressure-sensitive CCe-HVAC system (26)

CCe-HVAC system

CCe-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module CC

Communication module CC

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

DDG transducer

DDG transducer

DDG power supply unit

DDG power supply unit

Extension kit differential pressure sensor for Y-piece application

Extension kit differential pressure sensor for Y-piece application

Continuous, infinitely variable control, temperature-dependent CCe-HVAC system (24)

CCe-HVAC system

CCe-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module CC

Communication module CC

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Temperature module

Temperature module

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

Continuous, infinitely variable control, differential pressure-sensitive SCe-HVAC system (18)

SCe-HVAC system

SCe-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector