Wilo-DrainLift WS 40/50 Basic | Wilo

Wilo-DrainLift WS 40/50 Basic

Wilo-DrainLift WS 40/50

Eripärad / toote eelised

Survekindel kogumiskaev põrandapealseks ja põrandaaluseks paigaldamiseks
Vabalt valitavate sisendite tõttu paindlik
Suuremahuline paak
Koos torustiku, nivoo juhtimise, lülitusseadise ja pumbaga

Soovitatavad teenused

Konstruktsioon

Plastic shaft as a single or double pump system. Suitable for installation in the ground (underground) or in buildings (floor-mounted).

Fluid

For collection and pumping in commercial areas of:

Sewage without faeces
Wastewater (with small amounts of sand and gravel)

Wastewater pumping according to 12050

The pump shaft with the specified pump meets the requirements of EN 12050-2.

Construction

Shaft

Pump shaft with optimised geometry for deposit-free operation. Shaft body with ribbing for high rigidity and buoyancy safety. The inlets are freely selectable. Two transport eyes are integrated for attaching lifting equipment. The upwardly curved shaft cover is walkable and can carry a maximum load of 200 kg. The pump shaft is equipped with a floor mounting for installation in buildings.

Piping

Pressure pipe with threaded connection on the pump side
Shut-off valve
Non-return ball valve

Pump

Submersible sewage pump for three-phase AC connection (three-phase connection). Surface-cooled motor with thermal motor protection and bare cable ends.

Level control

Level control with a switching device and a level sensor. When the switch-off level is reached, the pump switches off after the follow-up time.

Scope of delivery

Plastic shaft with built-in piping, pump and level control
- Piping with shut-off valve and non-return ball valve
- Pump
- Switching device
- Level sensor
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

Rakendus

As a lifting unit within buildings (above ground installation).
As a pump chamber outside buildings (concealed floor installation).
For backflow resistant drainage of
- Drainage points below the backflow level
- Drainage points that cannot be drained via the natural downward slope.

Vedelikud

For collection and pumping in commercial areas of:

Sewage with faeces
Sewage without faeces
Wastewater (with small amounts of sand)

Wastewater pumping according to 12050

EN 12050-1:

DrainLift WS50E BASIC/M3-06-523/0-EF
DrainLift WS50E BASIC/U-06-523/0-EF
DrainLift WS50D BASIC/M3-06-523/1-O
DrainLift WS50D BASIC/U-06-523/1-O
DrainLift WS40E BASIC/M3S-08-523/0-EF
DrainLift WS40E BASIC/M3S-08-540/3-O
DrainLift WS40E BASIC/F3S-015-523/3-O

EN 12050-2:

DrainLift WS40E BASIC/M3-06-523/0-EF
DrainLift WS40E BASIC/M3-06-540/3-O
DrainLift WS40D BASIC/M3-06-523/3-O
DrainLift WS40D BASIC/M3-06-540/3-O

Varustus/funktsioon

Shut-off valve
Non-return valve
Switching device (depending on type)
Level control with float switch or level sensor
Submersible pump with thermal motor monitoring

Tüübikood

Example:	DrainLift WS40D BASIC/M3-06-523/3-O
DrainLift	Product family
WS	Pump chamber
40	Nominal size of discharge port: 40: G 2/50 mm 50: G 2½ /63 mm
D	Design pump chamber: E = single pump system D = double pump system
BASIC	Pump chamber with pump and level control
M3	Pre-installed pump: M3 = Rexa MINI3 M3S = Rexa MINI3-S U3 = Rexa UNI F3S = Rexa FIT-S03
06	Value/10 = rated power P2 of the pump in kW
5	Mains frequency: 5 = 50 Hz, 6 = 60 Hz
23	Code for rated voltage: 23 = 1~230 V 40 = 3~400 V
3	Design of pump and switch gear: 1 = operation type: S3, switch gear: Control MS-L 3 = operation type: S3, switch gear: Control EC-L
O	Design connection cable: EF = with CEE7/7 plug O = without connection cable

Tehnilised andmed

Tank volume: 255 l/67 US.liq.gal. (WS...E)/400 l/105 US.liq.gal. (WS...D)

Maximum pressure in discharge pipe: 6 bar (87 psi)

Discharge port: G 2/50 mm (WS 40), G 2½ /63 mm (WS 50)

Inlet connection: DN/OD 32 up to DN/OD 160 or DN 200

Venting connection: DN/OD 75

Mains connection: 1~230 V, 50 Hz or 3~400 V, 50 Hz

Fluid temperature: 3 ... 40 °C (37 ... 104 °F), max. 65 °C (149 °F) für 5 min

Ambient temperature max.: 3 ... 40 °C (37 ... 104 °F)

Materjalid

Pump chamber

Pump chamber: PE
Piping: PVC
Shut-off valve: PVC
Non-return valve: PPS

Sewage pump (without macerator)

Rexa MINI3
- Hydraulics housing: EN-GJL-200 (ASTM A48 Class 30)
- Impeller: PK-GF30
- Motor housing: 1.4301 (AISI 304)
- Sealing, on pump side: C/MgSi
- Sealing, on motor side: NBR
Rexa UNI
- Hydraulics housing: PP-GF30
- Impeller: PP-GF30
- Motor housing: 1.4301 (AISI 304)
- Sealing, on pump sideg: SiC/SiC
- Sealing, on motor side: C/Cr

Sewage pump (with macerator)

Rexa MINI3-S
- Hydraulics housing: EN-GJL-200 (ASTM A48 Class 30)
- Impeller: EN-GJL-250 (ASTM A48 Class 35/40B)
- Macerator: 1.4528/59 HRC (AISI 440B+Co)
- Motor housing: 1.4301 (AISI 304)
- Sealing, on pump side: SiC/SiC
- Sealing, on motor side: NBR
Rexa FIT-S
- Hydraulics housing: EN-GJL-200 (ASTM A48 Class 30)
- Impeller: EN-GJL-250 (ASTM A48 Class 35/40B)
- Macerator: 1.4528/59 HRC (AISI 440B+Co)
- Motor housing: 1.4301 (AISI 304)
- Sealing, on pump side: SiC/SiC
- Sealing, on motor side: C/MgSiO4

Tarnekomplekt

Design with sewage pumps without macerator

DrainLift WS40E BASIC/ ... /0-EF und DrainLift WS50E BASIC/ ... /0-EF

Plastic shaft with built-in piping, pump and level control
- Piping with shut-off valve and non-return ball valve
- Pump with float switch and plug
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

DrainLift WS40E BASIC/ ... /3-O und DrainLift WS40D BASIC/ ... /3-O

- Piping with shut-off valve and non-return ball valve
- Pump
- Switchgear
- Level sensor
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

DrainLift WS50D BASIC/ ... /1-O

Plastic shaft with built-in piping, pump and level control
- Piping with shut-off valve and non-return ball valve
- Pump
- Switchgear
- Float switch
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

Ausführungen mit Abwasserpumpen mit Schneidwerk

DrainLift WS40E BASIC/ ... /0-EF

Plastic shaft with built-in piping, pump and level control
- Piping with shut-off valve and non-return ball valve
- Pump with float switch and plug
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

DrainLift WS40E BASIC/ ... /3-O

Plastic shaft with built-in piping, pump and level control
- Piping with shut-off valve and non-return ball valve
- Pump
- Switchgear
- Level sensor
- Float switch
Shaft cover with seal
Connection set DN/OD 50 for drainage connection
Inlet set with hole saw (124 mm/5 in) and seal DN/OD 110
Floor mounting
Installation and operating instructions

Paigaldus- ja kasutusjuhend