CronoBloc-BL 32/230.1-5,5/2

Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed.

Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter.

Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment.

Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay.

Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n= f(T)
• Speed setter, n=f(analogue In)
• Temperature control, T-c
• Differential pressure - constant, dT
• Differential pressure - variable, dT-v
• Other types of control on request

Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:

• Signal and all drives full load
• Signal and system shut-down
• Signal and one pump at speed adjustable on frequency converter

Extra charge for optional modules (installation in factory or later after technical clarification):

• For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server
• For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request.
• for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals.
• Evaluation relay for PTC, individual operation and fault signals.
• Battery-backed power supply unit
• Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc.

Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model.

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.

Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks.

The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc.

Version

Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail.

Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required.

Scope of delivery

• BACnet IP module
• Connecting cable earth
• Installation and operating instructions

Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:

• Operation pumps 1-2
• Operation frequency converter
• Malfunction pump 1-2
• Malfunction frequency converter
• Frost message (version HVAC)
• Low water (water supply)

in conjunction with the base module GLT and the connection cable signalling modules.

Version: Relay module with operating status LED's, secured on 35 mm DIN rail

Scope of delivery

• 1 signalling module
• 2 support bases
• 2 spacers
• 1 DIN rail
• 2 M4x10 screws

Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.

Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:

• Up to 25 m: 3 x 0.75 mm², shielded.
• Up to 250 m: 3 x 1.5 mm², shielded.

Notice: not applicable with VR-HVAC

Scope of delivery

• 1 x differential pressure sensor
• 2 x cutting ring screw connections DIN 3862 Ød = 6 mm
• 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm
• 5 m connection cable to the switchgear (3 x 0.34 mm²)
• 1x holder for the differential pressure sensor
• 2 screws for mounting the differential pressure sensor
• Copper coil required on-site

Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:

• Up to 25 m: 3 x 0.75 mm², shielded.
• Up to 250 m: 3 x 1.5 mm², shielded.

Notice: not applicable with VR-HVAC

Scope of delivery

• 1 x differential pressure sensor
• 2 x cutting ring screw connections DIN 3862 Ød = 6 mm
• 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm
• 5 m connection cable to the switchgear (3 x 0.34 mm²)
• 1x holder for the differential pressure sensor
• 2 screws for mounting the differential pressure sensor
• Copper coil required on-site

Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed.

Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter.

Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment.

Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay.

Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n= f(T)
• Speed setter, n=f(analogue In)
• Temperature control, T-c
• Differential pressure - constant, dT
• Differential pressure - variable, dT-v
• Other types of control on request

Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:

• Signal and all drives full load
• Signal and system shut-down
• Signal and one pump at speed adjustable on frequency converter

Extra charge for optional modules (installation in factory or later after technical clarification):

• For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server
• For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request.
• for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals.
• Evaluation relay for PTC, individual operation and fault signals.
• Battery-backed power supply unit
• Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc.

Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model.

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.

Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks.

The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc.

Version

Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail.

Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required.

Scope of delivery

• BACnet IP module
• Connecting cable earth
• Installation and operating instructions

Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:

• Operation pumps 1-2
• Operation frequency converter
• Malfunction pump 1-2
• Malfunction frequency converter
• Frost message (version HVAC)
• Low water (water supply)

in conjunction with the base module GLT and the connection cable signalling modules.

Version: Relay module with operating status LED's, secured on 35 mm DIN rail

Scope of delivery

• 1 signalling module
• 2 support bases
• 2 spacers
• 1 DIN rail
• 2 M4x10 screws

Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing.

Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology.

• Feed temperature (TV)
• Return temperature (TR)
• Process temperature (TP)
• Outside temperature (TA)

Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.

Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:

• Operation pumps 1-2
• Operation frequency converter
• Malfunction pump 1-2
• Malfunction frequency converter
• Frost message (version HVAC)
• Low water (water supply)

in conjunction with the base module GLT and the connection cable signalling modules.

Version: Relay module with operating status LED's, secured on 35 mm DIN rail

Scope of delivery

• 1 signalling module
• 2 support bases
• 2 spacers
• 1 DIN rail
• 2 M4x10 screws

Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:

• Up to 25 m: 3 x 0.75 mm², shielded.
• Up to 250 m: 3 x 1.5 mm², shielded.

Notice: not applicable with VR-HVAC

Scope of delivery

• 1 x differential pressure sensor
• 2 x cutting ring screw connections DIN 3862 Ød = 6 mm
• 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm
• 5 m connection cable to the switchgear (3 x 0.34 mm²)
• 1x holder for the differential pressure sensor
• 2 screws for mounting the differential pressure sensor
• Copper coil required on-site

Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:

• Up to 25 m: 3 x 0.75 mm², shielded.
• Up to 250 m: 3 x 1.5 mm², shielded.

Notice: not applicable with VR-HVAC

Scope of delivery

• 1 x differential pressure sensor
• 2 x cutting ring screw connections DIN 3862 Ød = 6 mm
• 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm
• 5 m connection cable to the switchgear (3 x 0.34 mm²)
• 1x holder for the differential pressure sensor
• 2 screws for mounting the differential pressure sensor
• Copper coil required on-site

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications.

SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection.

Hardware

Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Differential pressure - variable, dp-v
• Temperature setter, n = f(Tx)
• Speed setter, n=f(analogue In)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Immunity for Industrial Environments EN 61000-6-2
• EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Wiring diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications.

SC version: for the control of conventional fixed speed pumps via contactors (cascade connection).

Hardware

Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables

• Pressure - constant, p-c
• Differential pressure - constant, dp-c
• Temperature setter, n = f(Tx)
• Differential pressure - constant, dT

Software functions

Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers.

2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters)

Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system.

Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning.

Automatic, configurable pump cycling

• Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours
• Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours

Automatic pump trial run (pump kick)

• Can be activated
• Time between two pump trial runs is freely programmable

Standards followed

• Electrical Equipment of Machines EN 60204-1
• Low-voltage switchgear combinations EN 61439-1 and 61439-2
• EMC - Interference immunity for Industrial Environments EN 61000-6-2
• EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises)

Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):

• H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller).
• Evaluation relay for PTC
• Individual running and fault signals
• Converter 0/2-10 V in 0/4 to 20 mA
• Soft starter for peak-load pumps
• Connection to BMS systems in accordance with VDI 3814
• Bus systems: BACnet, LON, Modbus RTU

Scope of delivery

• Switchgear
• Installation and operating instructions
• Circuit diagram

Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.

Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:

• Operation pumps 1-2
• Operation frequency converter
• Malfunction pump 1-2
• Malfunction frequency converter
• Frost message (version HVAC)
• Low water (water supply)

in conjunction with the base module GLT and the connection cable signalling modules.

Version: Relay module with operating status LED's, secured on 35 mm DIN rail

Scope of delivery

• 1 signalling module
• 2 support bases
• 2 spacers
• 1 DIN rail
• 2 M4x10 screws