Atmos GIGA-I 80/200-5,5/4 | Wilo

Atmos GIGA-I 80/200-5,5/4

Article number: 2222620

Hydraulic data
Minimum efficiency index (MEI)	≥0.4
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Max. ambient temperature T_max	40 °C
Maximum operating pressure PN	16 bar
Note on dimensioning	16 bar to 120 °C, 13 bar to 140 °C

Motor data
Mains connection	3~400 V, 50 Hz
Number of poles	4
Voltage tolerance	±10 %
Motor efficiency class	IE3
Rated power P₂	5.5 kW
Rated current I_N	11.1 A
Rated speed n	1450 1/min
Power factor cos φ₁₀₀	0.79
Motor efficiency 50% η_M50%	86.8 %
Motor efficiency 75% η_M75%	89 %
Motor efficiency 100% η_M100%	89.5 %
Insulation class	F
Protection class motor	IP55
Motor protection	PTC integrated

Materials
Pump housing	5.1301/EN-GJL-250 KTL-coated
Impeller	Grey cast iron EN-GJL-200
Shaft	Stainless steel
Mechanical seal	AQ1EGG
Lantern	5.1301/EN-GJL-250 KTL-coated

Installation dimensions
Pipe connection on the suction side DNs	DN 80
Pipe connection on the discharge side DNd	DN 80
Port-to-port length L0	500 mm

Atmos GIGA-I 80/200-5,5/4

∆: Connection diagram delta connection

Y: Connection diagram star connection

Motor protection switch required on-site. Check the direction of rotation! To change the direction of rotation, exchange any two phases.

P₂≤ 3 kW	3~400 V Y
	3~230 V ∆
P₂≥ 4 kW	3~690 V Y
	3~400 V ∆

After removing the bridges, Y-∆ start is possible.

Product data
Brand	Wilo
Product description	Atmos GIGA-I 80/200-5,5/4
Article number	2222620
EAN number	4062679256726
Colour	Green
Minimum order quantity	1
Date of sales availability	2022-07-01

Packaging
Packaging type	Euro pallet
Packaging property	Transport packaging
Pieces per pallet	1
Number per layer	1

Dimension, weight
Length with packaging	1200 mm
Length L	769 mm
Height with packaging	644 mm
Height H	500 mm
Width with packaging	800 mm
Width W	317 mm
Gross weight, approx. m	170 kg
Net weight, approx. m	145 kg

Single-stage glanded centrifugal pump with in-line design for pipe installation or installation on a base. Low-oscillation and low-noise monobloc design with lantern and rigidly connected standard flange motor. With forced-flow circulation, bidirectional bellows mechanical seal and cavitation-reducing impeller. From kW 37 with a cartridge mechanical seal in the back pull-out system for mechanical seal replacement without dismantling the motor. Flange with R 1/8 pressure measuring connections.

All grey cast iron components are cataphoretic-coated.

Pumps with motors ≥ 5.5 kW are equipped as standard with a PTC thermistor sensor for motor protection.

The motor terminal box ≤ 7.5 kW can be made of metal or plastic. If a metal terminal box is absolutely necessary, please order the appropriate special variant. The motor terminal boxes > 7.5 kW are always made of metal.

Mechanical seal for pumping water up to Tmax = +140 °C. Up to T ≤ +40 °C, a glycol admixture of 20 % to 40 % by volume is permissible. An alternative mechanical seal must be provided for water-glycol mixtures with a glycol content of > 40% to max. 50% by volume and a fluid temperature of > +40 °C to max. +120 °C or other fluids that differ from water. When using water-glycol mixtures, the use of an S1 variant with a corresponding mechanical seal is generally recommended.

Operating Data
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Min. ambient temperature T_min	0 °C
Max. ambient temperature T_max	40 °C
Maximum operating pressure PN	16 bar
Note on dimensioning	16 bar to 120 °C, 13 bar to 140 °C
Minimum efficiency index (MEI)	≥0.4

Motor data
Motor efficiency class	IE3
Mains connection	3~400 V, 50 Hz
Voltage tolerance	±10 %
Rated power P₂	5500 W
Rated speed n	1450 1/min
Rated current I_N	11.1 A
Power factor cos φ₁₀₀	0.79
Motor efficiency 50% η_M50%	86.8 %
Motor efficiency 75% η_M75%	89 %
Motor efficiency 100% η_M100%	89.5 %
Insulation class	F
Protection class	IP55

Materials
Pump housing	5.1301/EN-GJL-250 KTL-coated
Impeller	Grey cast iron
Shaft	Stainless steel
Shaft seal	AQ1EGG
Lantern	5.1301/EN-GJL-250 KTL-coated

Installation dimensions
Pipe connection on the suction side DNs	DN 80
Pipe connection on the discharge side DNd	DN 80

Ordering information
Brand	Wilo
Product description	Atmos GIGA-I 80/200-5,5/4
Net weight, approx. m	145 kg
Article number	2222620

Installation and operating instructions

Wilo-Atmos GIGA-I/-D/-B

Article Number	2230372
Edition	2023-06
Number of pages	148
Language	de, en, fr, nl

PDF (7 MB)

Wilo-Atmos GIGA-I/-D/-B

Article Number	2230376
Edition	2023-06
Number of pages	72
Language	en, zh

PDF (7 MB)

Wilo-Atmos GIGA-I/-D/-B

Article Number	2230371
Edition	2023-06
Number of pages	40
Language	en

PDF (6 MB)

Group Statement

Group Statement REACH

Edition	2021-05
Number of pages	5
Language	language neutral

PDF (279 KB)

Continuous, infinitely variable control, differential pressure-sensitive CC-HVAC system (26)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x13A-T34-SD-FC-BM	2527830
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x13A-T34-SD-FC-BM	2527831
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x13A-T34-SD-FC-BM	2527832
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module Profibus
Communication module Profibus	Communication module Profibus DP	2533866
Communication module Profibus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Profibus DP networks. The Profibus DP communications module represents an extension to the integration of a CC/CCe system in an already existing Profibus network. The connection of the Profibus module takes place via corresponding Profibus plugs (not included in the scope of delivery). Certain parameters can be written and read via Profibus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Profibus DP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Profibus DP Connecting cable earth Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG (4-20mA)
DDG (4-20mA)	Wilo-DDG 10 Signal Trans.(4-20mA)2G VP.	2136454
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 100 Signal Trans.(4-20mA)	2211740
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 20 Signal Trans.(4-20mA)2G VP.	2136456
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 40 Signal Trans.(4-20mA)2G VP.	2136458
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 60 Signal Trans.(4-20mA)2G VP.	2136460
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, temperature-dependent CC-HVAC system (22)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x13A-T34-SD-FC-BM	2527830
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x13A-T34-SD-FC-BM	2527831
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x13A-T34-SD-FC-BM	2527832
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module Profibus
Communication module Profibus	Communication module Profibus DP	2533866
Communication module Profibus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Profibus DP networks. The Profibus DP communications module represents an extension to the integration of a CC/CCe system in an already existing Profibus network. The connection of the Profibus module takes place via corresponding Profibus plugs (not included in the scope of delivery). Certain parameters can be written and read via Profibus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Profibus DP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Profibus DP Connecting cable earth Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, differential pressure-sensitive SC-HVAC system (33)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-FC-HVAC system 1x12A-FC-BM (direct starting)	2545446
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 1x13A-FC-BM (star-delta-starting)	2545466
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x12A-FC-BM (direct starting)	2545447
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x13A-FC-BM (star-delta-starting)	2545467
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x12A-FC-BM (direct starting)	2545448
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x13A-FC-BM (star-delta-starting)	2545468
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x12A-FC-BM (direct starting)	2545449
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x13A-FC-BM (star-delta-starting)	2545469
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-HVAC system 1x12A-WM (direct starting)	2545330
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x13A-WM (star-delta-starting)	2545350
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x12A-WM (direct starting)	2545331
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x13A-WM (star-delta-starting)	2545351
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x12A-WM (direct starting)	2545332
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x13A-WM (star-delta-starting)	2545352
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x12A-WM (direct starting)	2545333
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x13A-WM (star-delta-starting)	2545353
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
DDG (4-20mA)
DDG (4-20mA)	Wilo-DDG 10 Signal Trans.(4-20mA)2G VP.	2136454
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 100 Signal Trans.(4-20mA)	2211740
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 20 Signal Trans.(4-20mA)2G VP.	2136456
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 40 Signal Trans.(4-20mA)2G VP.	2136458
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 60 Signal Trans.(4-20mA)2G VP.	2136460
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, temperature-dependent SC-HVAC system (27)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-FC-HVAC system 1x12A-FC-BM (direct starting)	2545446
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 1x13A-FC-BM (star-delta-starting)	2545466
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x12A-FC-BM (direct starting)	2545447
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x13A-FC-BM (star-delta-starting)	2545467
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x12A-FC-BM (direct starting)	2545448
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x13A-FC-BM (star-delta-starting)	2545468
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x12A-FC-BM (direct starting)	2545449
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x13A-FC-BM (star-delta-starting)	2545469
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-HVAC system 1x12A-WM (direct starting)	2545330
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x13A-WM (star-delta-starting)	2545350
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x12A-WM (direct starting)	2545331
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x13A-WM (star-delta-starting)	2545351
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x12A-WM (direct starting)	2545332
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x13A-WM (star-delta-starting)	2545352
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x12A-WM (direct starting)	2545333
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x13A-WM (star-delta-starting)	2545353
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.

Pipe installation, adapter fitting (5)
Adapter set glanded pumps
Adapter set glanded pumps	Adapter A80-50 Set, DN 80x50mm, PN 16	2085212
	Adapter including fastening and sealing material for adjusting the overall length l0 to current pump series. Scope of delivery 1 adapter 2 flat gaskets Fixation material: 8 bolts with nuts
	Adapter A80-60 SET, DN 80x60mm, PN 16	2085213
	Adapter including fastening and sealing material for adjusting the overall length l0 to current pump series. Scope of delivery 1 adapter 2 flat gaskets Fixation material: 8 bolts with nuts
	Adapter A80-10 Set, DN 80x10mm, PN 16	2085472
	Adapter including fastening and sealing material for adjusting the overall length l0 to current pump series. Scope of delivery 1 adapter 2 flat gaskets Fixation material: 8 bolts with nuts
Intermediate flange connecting piece F
Intermediate flange connecting piece F	Intermediate flange pieces F 30, DN 80x25mm, PN 10/16	110681991
	The Wilo-F flange intermediate connecting pieces are used for compensation of the port-to-port length in case of a pump replacement. They are made of grey cast iron and are provided for length compensation of flange connections. The washers included in the scope of delivery must be used for pumps that have combination flanges. Scope of delivery 1 flange intermediate piece F 2 seals Screws/nuts (number and size based on flange version)
	Intermediate flange pieces F 42, DN 80x140mm, PN 10/16	2101158
	The Wilo-F flange intermediate connecting pieces are used for compensation of the port-to-port length in case of a pump replacement. They are made of stainless steel and are provided for length compensation of flange connections also in domestic hot water circulation systems. The washers included in the scope of delivery must be used for pumps that have combination flanges. Scope of delivery 1 flange intermediate piece F 2 seals Screws/nuts and washers (number and size based on flange version)
Wall fixation/installation on a base (1)
Mounting bracket kit
Mounting bracket kit	Mounting bracket F 3-14 SET	2040968
Mounting bracket kit	Mounting brackets for the installation on a base of in-line and monobloc pumps. Comprised of several angle brackets (number dependent on the pump type), intended for the screwed connection with the screw-on bases or feet of the pump. The angle brackets ensure secure fastening of the pump to the foundation. Including fixation material. Notice The mounting brackets / angle brackets must be lined by the dimension specified for the following pump types: BL 65/270-5.5/4, BL 80/250-5.5/4, BL/BL-E 80/250-7.5/4: 30 mm all types BL 100/..., BL 125/220..., BL/BL-E 125/260..., BL/BL-E 125/270...: 20 mm all types BL 125/190..., BL 125/200..., BL 125/250...: 40 mm Scope of delivery Screws Angle brackets Screw stays Nuts

Pump control (1)
Wilo-EFC
Wilo-EFC	EFC5.5 3x380-480V 50/60Hz IP55	2193437
Wilo-EFC	A stand-alone frequency converter for fixed-speed pumps that are operated in variable applications, especially for heating, air conditioning and pressure boosting. Special features/product advantages Compact design with an energy-saving cooling concept for lowering temperature losses Integrated energy-efficient harmonic reduction function in the pump’s partial load range Versatile pumping application scenarios thanks to differing connection options and different control modes Simple commissioning thanks to an intuitive assistant with graphical user interface Options External communication via IF modules (optional): Profibus, DeviceNet, Profinet, Ethernet, Modbus Scope of delivery Stand-alone frequency converter Installation and operating instructions
Pump control/accessories (30)
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	SMA/FME adapter	2545548
	Koaxialer Steckverbinder SMA-Stecker auf FME-Stecker in kompakten Bauform mit Schraubverschluss. Einsetzbar bis 2 GHz, der Wellenwiderstand beträgt 50 Ω.
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
Communication module CC
Communication module CC	CC communication module	2533850
Communication module CC	Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery Communication module CC Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module Profibus
Communication module Profibus	Communication module Profibus DP	2533866
Communication module Profibus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Profibus DP networks. The Profibus DP communications module represents an extension to the integration of a CC/CCe system in an already existing Profibus network. The connection of the Profibus module takes place via corresponding Profibus plugs (not included in the scope of delivery). Certain parameters can be written and read via Profibus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Profibus DP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Profibus DP Connecting cable earth Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Output filter EFC (150-500 m cable length)
Output filter EFC (150-500 m cable length)	17 A sin IP54 Wilo-EFC filter	6084563
	Output filter for Wilo-EFC
	17 A sin IP00 Wilo-EFC filter	6084578
	Output filter for Wilo-EFC
	17 A sin IP20 Wilo-EFC filter	6084904
	Output filter for Wilo-EFC
Output filter EFC du/dt (up to 150m cable length)
Output filter EFC du/dt (up to 150m cable length)	40 A du/dt IP54 Wilo-EFC filter	6084544
Output filter EFC du/dt (up to 150m cable length)	Output filter for Wilo-EFC
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
	BACnet IP SC communication module	2553366
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe booster with BACnet IP networks. The communication module SC-OPTION BACnet IP is a hardware extension and optionally a software extension to connect an SC/SCe system as a participant in an existing BACnet IP building automation. The connection of the BACnet IP module to the RS485 bus takes place via twisted-pair cabling. BACnet (Building Automation and Control Networks) IP ensures interoperability between devices from different manufacturers. With BACnet IP, different parameters can be read and written, e.g. switchgear data, pump status and modes, actual values, setpoints, the current speed of the pump, measured temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Only Wilo customer service can perform a subsequent activation and installation of the BACnet IP function in the switchgear. Scope of delivery BACnet IP module Fixation material Connecting cable Activation code Installation and operating instructions
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Pump control/Comfort control system (3)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x13A-T34-SD-FC-BM	2527830
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x13A-T34-SD-FC-BM	2527831
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x13A-T34-SD-FC-BM	2527832
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Pump control/Smart control system (16)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-HVAC system 1x12A-WM (direct starting)	2545330
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x12A-WM (direct starting)	2545331
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x12A-WM (direct starting)	2545332
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x12A-WM (direct starting)	2545333
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x13A-WM (star-delta-starting)	2545350
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x13A-WM (star-delta-starting)	2545351
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x13A-WM (star-delta-starting)	2545352
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x13A-WM (star-delta-starting)	2545353
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-FC-HVAC system 1x12A-FC-BM (direct starting)	2545446
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x12A-FC-BM (direct starting)	2545447
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x12A-FC-BM (direct starting)	2545448
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x12A-FC-BM (direct starting)	2545449
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selecte

Atmos GIGA-I 80/200-5,5/4

Atmos GIGA-I 80/200-5,5/4

Installation and operating instructions

Wilo-Atmos GIGA-I/-D/-B

Wilo-Atmos GIGA-I/-D/-B

Wilo-Atmos GIGA-I/-D/-B

Group Statement

Group Statement REACH

Continuous, infinitely variable control, differential pressure-sensitive CC-HVAC system (26)

CC-HVAC system

CC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module Profibus

Communication module Profibus

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

DDG (4-20mA)

DDG (4-20mA)

PTC thermistor tripping unit

PTC thermistor tripping unit

Continuous, infinitely variable control, temperature-dependent CC-HVAC system (22)

CC-HVAC system

CC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module Profibus

Communication module Profibus

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Temperature module

Temperature module

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

PTC thermistor tripping unit

PTC thermistor tripping unit

Continuous, infinitely variable control, differential pressure-sensitive SC-HVAC system (33)

SC/SC-FC-HVAC system

SC/SC-FC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector

Communication module LON (SC)

Communication module LON (SC)

SC communication module BACnet