Atmos GIGA-N 100/250-15/4 | Wilo

Atmos GIGA-N 100/250-15/4

Article number: 6086225

Hydraulic data
Maximum operating pressure PN	16 bar
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Min. ambient temperature T_min	-15 °C
Max. ambient temperature T_max	40 °C

Motor data
Mains connection	3~400 V, 50 Hz
Voltage tolerance	±10 %
Rated power P₂	15 kW
Motor efficiency class	IE3
Rated current I_N	27.9 A
Rated speed n	1465 1/min
Power factor cos φ₁₀₀	0.78
Insulation class	F
Protection class motor	IP55

Installation dimensions
Pipe connection on the suction side DNs	DN 125
Pipe connection on the discharge side DNd	DN 100

Materials
Pump housing	Grey cast iron
Impeller	Grey cast iron
Shaft	Stainless steel
Mechanical seal	AQ1EGG
Lantern	Grey cast iron

Atmos GIGA-N 100/250-15/4

∆: Connection diagram delta connection

Y: Connection diagram star connection

Motor protection switch required on-site. Check the direction of rotation! To change the direction of rotation, exchange any two phases.

P₂≤ 3 kW	3~400 V Y
	3~230 V ∆
P₂≥ 4 kW	3~690 V Y
	3~400 V ∆

After removing the bridges, Y-∆ start is possible.

Product data
Brand	Wilo
Product description	Atmos GIGA-N 100/250-15/4
Article number	6086225
EAN number	4048482978727
Colour	Green
Minimum order quantity	1
Date of sales availability	2019-03-01

Packaging
Packaging type	Special pallet
Packaging property	Transport packaging
Pieces per pallet	1
Number per layer	1

Dimension, weight
Length with packaging	1900 mm
Length L	1470 mm
Height with packaging	748 mm
Height H	608 mm
Width with packaging	800 mm
Width W	610 mm
Gross weight, approx. m	451 kg
Net weight, approx. m	408 kg

Single-stage centrifugal pump as baseplate pump in accordance with EN 733, with axial suction ports and radial pressure ports for installation on a base. Pump with support foot and flanged bearing bracket, coupling, coupling guard and motor mounted to same baseplate.

IEC motor with 3 PTC thermistor sensors. Shaft sealing with bidirectional bellows mechanical seal. Grey cast iron housing, stainless steel shaft, grey cast iron impeller. Cataphoretic coating as standard for all cast iron components in contact with fluid.

Coupling variants:

Spacer coupling (standard)
Elastic coupling (variant P5, at a reduced price)

Impeller variants (for an additional charge):

Bronze
Stainless steel

NOTICE

The elastic coupling does not contain a spacer.

The spacer coupling is an elastic coupling with a spacer. The spacer reduces maintenance costs, and further motor orientation when changing the mechanical seal is not necessary.

Materials
Pump housing	Grey cast iron
Impeller	Grey cast iron
Lantern	Grey cast iron
Shaft	Stainless steel
Shaft seal	AQ1EGG

Operating Data
Min. fluid temperature T_min	-20 °C
Max. fluid temperature T_max	140 °C
Maximum operating pressure p	16.0 bar
Max. ambient temperature T_max	40 °C
Minimum efficiency index (MEI)	≥0.4

Motor data
Mains connection	3~400 V, 50 Hz
Voltage tolerance	±10 %
Motor efficiency class	IE3
Rated power P₂	15000 W
Rated speed n	1465 1/min
Rated current I_N	27.9 A
Power factor cos φ₁₀₀	0.78
Motor efficiency 50% η_M50%	92.2 %
Motor efficiency 75% η_M75%	92.5 %
Motor efficiency 100% η_M100%	92.3 %
Protection class	IP55
Insulation class	F

Installation dimensions
Pipe connection on the suction side DNs	DN 125
Pipe connection on the discharge side DNd	DN 100

Ordering information
Brand	Wilo
Net weight, approx. m	408 kg
Product description	Atmos GIGA-N 100/250-15/4
Article number	6086225

Installation and operating instructions

Wilo-Atmos GIGA-N

Article Number	6074707
Edition	2019-04
Number of pages	1064
Language	bg, cs, da, de, el, en, es, et, fi, fr, hr, hu, it, lt, lv, nl, no, pl, pt, ro, ru, sk, sl, sr, sv, tr, uk, zh

PDF (8 MB)

Certification booklet

Wilo-Atmos GIGA-N, Wilo-Yonos GIGA-N

Article Number	6088790
Edition	2021-01
Number of pages	16
Language	en

PDF (3 MB)

Group Statement

Group Statement REACH

Edition	2021-05
Number of pages	5
Language	language neutral

PDF (327 KB)

Continuous, infinitely variable control, differential pressure-sensitive CC-HVAC system (27)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x32A-T34-SD-FC-BM	2527848
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x32A-T34-SD-FC-BM	2527849
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x32A-T34-SD-FC-BM	2527850
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG (4-20mA)
DDG (4-20mA)	Wilo-DDG 10 Signal Trans.(4-20mA)2G VP.	2136454
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 100 Signal Trans.(4-20mA)	2211740
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 20 Signal Trans.(4-20mA)2G VP.	2136456
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 40 Signal Trans.(4-20mA)2G VP.	2136458
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 60 Signal Trans.(4-20mA)2G VP.	2136460
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, temperature-dependent CC-HVAC system (21)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x32A-T34-SD-FC-BM	2527848
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x32A-T34-SD-FC-BM	2527849
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x32A-T34-SD-FC-BM	2527850
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, differential pressure-sensitive SC-HVAC system (35)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-FC-HVAC system 1x32A-FC-BM (direct starting)	2545462
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 1x32A-FC-BM (star-delta-starting)	2545482
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (direct starting)	2545463
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (star-delta-starting)	2545483
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (direct starting)	2545464
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (star-delta-starting)	2545484
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (direct starting)	2545465
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (star-delta-starting)	2545485
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-HVAC system 1x32A-WM (direct starting)	2545346
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x32A-WM (star-delta-starting)	2545366
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (direct starting)	2545347
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (star-delta-starting)	2545367
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-BM (star-delta-starting)	2545368
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-WM (direct starting)	2545348
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-BM (star-delta-starting)	2545369
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-WM (direct starting)	2545349
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
DDG (4-20mA)
DDG (4-20mA)	Wilo-DDG 10 Signal Trans.(4-20mA)2G VP.	2136454
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 100 Signal Trans.(4-20mA)	2211740
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 20 Signal Trans.(4-20mA)2G VP.	2136456
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 40 Signal Trans.(4-20mA)2G VP.	2136458
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 60 Signal Trans.(4-20mA)2G VP.	2136460
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.
Continuous, infinitely variable control, temperature-dependent SC-HVAC system (27)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-FC-HVAC system 1x32A-FC-BM (direct starting)	2545462
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 1x32A-FC-BM (star-delta-starting)	2545482
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (direct starting)	2545463
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (star-delta-starting)	2545483
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (direct starting)	2545464
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (star-delta-starting)	2545484
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (direct starting)	2545465
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (star-delta-starting)	2545485
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-HVAC system 1x32A-WM (direct starting)	2545346
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x32A-WM (star-delta-starting)	2545366
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (direct starting)	2545347
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (star-delta-starting)	2545367
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-BM (star-delta-starting)	2545368
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-WM (direct starting)	2545348
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-BM (star-delta-starting)	2545369
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-WM (direct starting)	2545349
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
SC communication module BACnet	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.

Pump control (1)
Wilo-EFC
Wilo-EFC	EFC15 3x380-480V 50/60Hz IP55	2193440
Wilo-EFC	A stand-alone frequency converter for fixed-speed pumps that are operated in variable applications, especially for heating, air conditioning and pressure boosting. Special features/product advantages Compact design with an energy-saving cooling concept for lowering temperature losses Integrated energy-efficient harmonic reduction function in the pump’s partial load range Versatile pumping application scenarios thanks to differing connection options and different control modes Simple commissioning thanks to an intuitive assistant with graphical user interface Options External communication via IF modules (optional): Profibus, DeviceNet, Profinet, Ethernet, Modbus Scope of delivery Stand-alone frequency converter Installation and operating instructions
Pump control/accessories (30)
Antenna GSM/GPRS
Antenna GSM/GPRS	D-network dual-band antenna with 3 m cable	2533862
	Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 10 m cable	2533863
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	D-network tri-band antenna 15 m cable	2533864
	Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul.
	SMA/FME adapter	2545548
	Koaxialer Steckverbinder SMA-Stecker auf FME-Stecker in kompakten Bauform mit Schraubverschluss. Einsetzbar bis 2 GHz, der Wellenwiderstand beträgt 50 Ω.
BMS base module
BMS base module	BMS base module	2533800
BMS base module	The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery BMS base module Installation and operating instructions
CC communication module BACnet
CC communication module BACnet	CC-communication module BACnet MS/TP (slave)	2537050
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet MS/TP communications module Earth connection cable Installation and operating instructions
	CC-communication module BACnet IP (slave)	2537051
	Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery BACnet IP module Connecting cable earth Installation and operating instructions
Communication module CC
Communication module CC	CC communication module	2533850
Communication module CC	Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery Communication module CC Installation and operating instructions
Communication module GSM
Communication module GSM	GSM module	2533861
Communication module GSM	Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module GSM Communication cable Power supply connection cable
Communication module GSM (SC)
Communication module GSM (SC)	Communication module GSM (SC)	2542216
Communication module GSM (SC)	Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery Communication module SC-OPTION GSM Communication module holder Power supply connection cable Communication cable
Communication module LON
Communication module LON	Communication module LON	2533868
Communication module LON	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module LON Connection cable Fixation material Installation and operating instructions
Communication module LON (SC)
Communication module LON (SC)	Communication module LON (SC)	2538243
Communication module LON (SC)	The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery Piggyback Installation and operating instructions
Communication module ModBus
Communication module ModBus	Communication module Modbus RTU	2533869
Communication module ModBus	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery Communication module Modbus RTU Connection cable connection terminals Installation and operating instructions
Connection cable control modules/signalling modules
Connection cable control modules/signalling modules	Control modules connecting cable	2533790
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
	Signalling modules connecting cable	2533890
	Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1.
DDG impulse selector
DDG impulse selector	DDG impulse selector	2533770
DDG impulse selector	Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery DDG impulse selector Power supply connection cable Terminal Installation and operating instructions
Outdoor temperature sensor Pt 100
Outdoor temperature sensor Pt 100	Outdoor temperature sensor Pt 100	2533772
Outdoor temperature sensor Pt 100	Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery Outdoor temperature sensor PT 100 On-site fixation material
Output filter EFC (150-500 m cable length)
Output filter EFC (150-500 m cable length)	32 A sin IP54 Wilo-EFC filter	6084565
	Output filter for Wilo-EFC
	38 A sin IP00 Wilo-EFC filter	6084580
	Output filter for Wilo-EFC
	38 A sin IP20 Wilo-EFC filter	6084906
	Output filter for Wilo-EFC
Output filter EFC du/dt (up to 150m cable length)
Output filter EFC du/dt (up to 150m cable length)	40 A du/dt IP54 Wilo-EFC filter	6084544
	Output filter for Wilo-EFC
	40 A du/dt IP20 Wilo-EFC filter	6084553
	Output filter for Wilo-EFC
Pump signalling module
Pump signalling module	Signalling module pump 1-2	2533812
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 1-2 Operation frequency converter Malfunction pump 1-2 Malfunction frequency converter Frost message (version HVAC) Low water (water supply) in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
	Signalling module pump 3-6	2533836
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as: Operation pumps 3-6 Malfunction pumps 3-6 in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery 1 signalling module 2 support bases 2 spacers 1 DIN rail 2 M4x10 screws
SC communication module BACnet
SC communication module BACnet	SC-communication module BACnet MS/TP (slave)	2538242
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery Release code Installation and operating instructions
	BACnet IP SC communication module	2553366
	For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe booster with BACnet IP networks. The communication module SC-OPTION BACnet IP is a hardware extension and optionally a software extension to connect an SC/SCe system as a participant in an existing BACnet IP building automation. The connection of the BACnet IP module to the RS485 bus takes place via twisted-pair cabling. BACnet (Building Automation and Control Networks) IP ensures interoperability between devices from different manufacturers. With BACnet IP, different parameters can be read and written, e.g. switchgear data, pump status and modes, actual values, setpoints, the current speed of the pump, measured temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Only Wilo customer service can perform a subsequent activation and installation of the BACnet IP function in the switchgear. Scope of delivery BACnet IP module Fixation material Connecting cable Activation code Installation and operating instructions
SC-HVAC signal board
SC-HVAC signal board	SC-HVAC signal board	2119646
SC-HVAC signal board	Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery 1 Signalling module 2 Support base 2 Spacer 1 DIN rail 2 M4x10 screw
Signal converter retrofit kit
Signal converter retrofit kit	Signal converter 0-10 V / 0-20 mA	2534992
Signal converter retrofit kit	additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery Signal converter Connection cable connection terminals Installation and operating instructions
Temperature module
Temperature module	Temperature module for systems with 4-6 pumps	2533771
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
	Temperature module for systems with 1-3 pumps	2534991
	Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology. Feed temperature (TV) Return temperature (TR) Process temperature (TP) Outside temperature (TA)
Pump control/Comfort control system (3)
CC-HVAC system
CC-HVAC system	CC-HVAC-System 1x32A-T34-SD-FC-BM	2527848
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 2x32A-T34-SD-FC-BM	2527849
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	CC-HVAC-System 3x32A-T34-SD-FC-BM	2527850
	Wilo-Comfort Controller for digital, stepless power control of one-pump and multiple-pump systems in heating, air-conditioning and ventilation applications. For conventional pumps with fixed speed. Completely electronic Comfort-Controller (CC) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices in addition to frequency converter and sine filter. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables: Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n= f(T) Speed setter, n=f(analogue In) Temperature control, T-c Differential pressure - constant, dT Differential pressure - variable, dT-v Other types of control on request Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from: Signal and all drives full load Signal and system shut-down Signal and one pump at speed adjustable on frequency converter Extra charge for optional modules (installation in factory or later after technical clarification): For connection to BMS systems in accordance with VDI 3814, via analogue/GSM modem, web server For connection to bus systems: Profibus, LON-Bus, CAN-Bus, Modbus RTU, Ethernet, others on request. for external remote setpoint adjustment (differential pressure level) or manual control mode using 0/2 - 10 V signals. Evaluation relay for PTC, individual operation and fault signals. Battery-backed power supply unit Measurement of electrical parameters, such as voltage, current, effective power, power factor, etc. Ordering example: Wilo CC-HVAC 6x11.0 FC BM: Switchgear for 6 pumps with P2=11.0 kW, with frequency converter & sine filter (FC=Frequency Converter), designed as switch cabinet floor model. Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Pump control/Smart control system (16)
SC/SC-FC-HVAC system
SC/SC-FC-HVAC system	SC-HVAC system 1x32A-WM (direct starting)	2545346
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (direct starting)	2545347
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-WM (direct starting)	2545348
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-WM (direct starting)	2545349
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 1x32A-WM (star-delta-starting)	2545366
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 2x32A-WM (star-delta-starting)	2545367
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 3x32A-BM (star-delta-starting)	2545368
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-HVAC system 4x32A-BM (star-delta-starting)	2545369
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air conditioning and ventilation applications. SC version: for the control of conventional fixed speed pumps via contactors (cascade connection). Hardware Fully electronic Wilo-Smart Controller (SC) in sheet metal enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft PLC”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of pump motors: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Actual value output via analogue signal 0-10 V for external measurement/display possibility, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Temperature setter, n = f(Tx) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Interference immunity for Industrial Environments EN 61000-6-2 EMC interference emission for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 interference emission industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Circuit diagram
	SC-FC-HVAC system 1x32A-FC-BM (direct starting)	2545462
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (direct starting)	2545463
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (direct starting)	2545464
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (direct starting)	2545465
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 1x32A-FC-BM (star-delta-starting)	2545482
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 2x32A-FC-BM (star-delta-starting)	2545483
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 3x32A-FC-BM (star-delta-starting)	2545484
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
	SC-FC-HVAC system 4x32A-FC-BM (star-delta-starting)	2545485
	Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. SC-FC version: For the control of conventional fixed speed pumps via contactors (cascade connection), but control of a pump via frequency converters as a base-load pump, control of the peak-load pumps in cascade connection. Hardware Fully electronic Wilo-Smart Controller (SC) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. Fuse protection of the pump motors and frequency converter: By motor protection switch in the direct starting version; by fusible cut-out in the star-delta-starting version in combination with thermal triggers. Contactors for switching on the pumps; star-delta-starting models include thermal triggering and a time relay for the star-delta combination. Frequency converter with sine filter for infinitely variable control of the base-load pump. Actual value output via analogue signal 0-10 V for external measurement/display option, 10 V corresponds to the sensor end value, input 0/4-20 mA for external setpoint adjustment. Automatic, load-sensitive cut-in from 1 to n peak-load pump(s) depending on the control variables Pressure - constant, p-c Differential pressure - constant, dp-c Differential pressure - variable, dp-v Temperature setter, n = f(Tx) Speed setter, n=f(analogue In) Differential pressure - constant, dT Software functions Fully automatic control for 1 to n pumps with frequency-controlled base-load pump by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling Standard setting: Impulse - The base-load pump is cycled at each new demand, regardless of operating hours Alternative: Pump cycling dependent on operating hours, cycling of the base-load pump after the specified operating hours Automatic pump trial run (pump kick) Can be activated Time between two pump trial runs is freely programmable Standards followed Electrical Equipment of Machines EN 60204-1 Low-voltage switchgear combinations EN 61439-1 and 61439-2 EMC - Immunity for Industrial Environments EN 61000-6-2 EMC emitted interference for domestic accommodation, trade and commercial premises and small companies EN 61000-6-3 (for SC-FC only to 7.5 kW, over this EN 61000-6-4 emitted interference industrial premises) Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification): H-0-A (Manual-Zero-Automatic) switch: preselection of the operating mode of each pump and manual operation in the event of a controller fault “Manual” (emergency/test mode available at mains power, motor protection available), “O” (pump switched off – cannot be switched on using the controller) and “Auto” (pump enabled for automatic mode via the controller). Evaluation relay for PTC Individual running and fault signals Converter 0/2-10 V in 0/4 to 20 mA Soft starter for peak-load pumps Connection to BMS systems in accordance with VDI 3814 Bus systems: BACnet, LON, Modbus RTU Scope of delivery Switchgear Installation and operating instructions Wiring diagram
Differential pressure detection (7)
DDG (4-20mA)
DDG (4-20mA)	Wilo-DDG 10 Signal Trans.(4-20mA)2G VP.	2136454
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 20 Signal Trans.(4-20mA)2G VP.	2136456
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 40 Signal Trans.(4-20mA)2G VP.	2136458
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 60 Signal Trans.(4-20mA)2G VP.	2136460
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
	Wilo-DDG 100 Signal Trans.(4-20mA)	2211740
	Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site: Up to 25 m: 3 x 0.75 mm², shielded. Up to 250 m: 3 x 1.5 mm², shielded. Notice: not applicable with VR-HVAC Scope of delivery 1 x differential pressure sensor 2 x cutting ring screw connections DIN 3862 Ød = 6 mm 2 x angle cutting ring screw connections R 1/8 x Ød = 6 mm 5 m connection cable to the switchgear (3 x 0.34 mm²) 1x holder for the differential pressure sensor 2 screws for mounting the differential pressure sensor Copper coil required on-site
DDG power supply unit
DDG power supply unit	DDG power supply unit	501865293
DDG power supply unit	Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery DDG power supply unit On-site fastening elements
DDG transducer
DDG transducer	DDG transducer	501771990
DDG transducer	DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable: Input: 2 x 1.5 mm2, 250 m max. length, shielded. Output: 2 x 1.5 mm2, 750 m max. length, shielded. Scope of delivery DDG transducer DDG power supply unit On-site fixation material
Motor protection (1)
PTC thermistor tripping unit
PTC thermistor tripping unit	PTC thermistor tripping unit	509275993
PTC thermistor tripping unit	PTC thermistor triggering relay for switch cabinet installation (1 device per motor required). The thermistor overload relays monitor motors which are equipped with PTC thermistor temperature sensors. The temperature sensors are installed in the windings of the motors and measure the heating up of the motor directly. This enables direct monitoring and evaluation of various operating conditions. A collective fault signal (SSM) is possible with corresponding wiring in the switch cabinet.

With Wilo as your partner, you can not only be sure of choosing high-quality product solutions, but also of benefiting from a comprehensive, worry-free package of well thought-out services. We collaborate to develop a service concept tailored to your individual needs; with our expertise and personal consultancy, we make sure that the operation of your systems is as energy-efficient, reliable and economical as possible. All the while our competent Wilo service technicians are ready to assist you with fast, reliable and on-time support.

Recommended services
Supervision	Supervision Norm-/SCP pumps	2219322
	Wilo supports during the concept phase to ensure quality work and cost efficiency. Our competent and qualified Wilo Service will support you with recommendations and technical advice throughout the entire project. Supervision includes: Regular on-site visits ensure the quality of information and advice Technical consultancy, also available on site Status report with recommendations after the visit Comprehensive support from a Wilo expert
Commissioning	Commissioning Norm-/SCP pumps	2160452
	For perfect functioning of the pump(s) / system(s), it is recommended to have the commissioning carried out by the works' own WILO SE Customer Service Department. Optimum setting and efficient operation of the system are ensured as a result. Commissioning is comprised of the following points: Commissioning of pump(s) according to checklist Functional check of pump(s) Alignment of pump(s) Practice-oriented operation instruction Wilo commissioning protocol The price for commissioning only applies to system(s) which have been installed in accordance with the installation and operating instructions and state-of-the-art technology. No costs for any materials which may be required are included. -NET-
Maintenance	Maintenance BASIC Norm-/SCP pumps	2160467
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. The price of the maintenance is valid inside Germany. -NET-
	Maintenance COMFORT Norm-/SCP pumps	2160482
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Review and, if necessary, adjustment of the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during normal service hours) Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. The price of the maintenance is valid inside Germany. -NET-
	Maintenance PREMIUM Norm-/SCP pumps	2160497
	In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points: Visual inspection of the pumps/systems Mechanical check Electrical check Testing and possible filling of pressure vessels that may be on hand Checking the system parameters Creating a maintenance protocol Consumable materials are included in the contract price Elimination of payroll and travel expenses for deployments between maintenance intervals (during and outside normal service hours) Software updates Includes wearing parts Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. The price of the maintenance is valid inside Germany. -NET-
Wilo-Live Assistant	Wilo-Live Assistant Service	2216415
	The Wilo-Live Assistant is a technical advisor at your side during pump service. By using the Wilo-Live Assistant, our expert advisers can support you in the boiler or equipment room via video transmission – live and in real time. You use your smartphone to show the installation set-up, while the Wilo expert follows everything on their screen. They can see the components as well as other details and can thus determine where the fault or breakdown originates. We prevent downtime and ensure operational reliability of your pumps and systems! The Wilo-Live Assistant includes: Interactive live support via video chat Direct contact with an expert Just-in-time solution to ensure maximum operational reliability of your pumps and systems
More suitable services
Service packages	Service Package L Norm-/SCP pumps	2219698
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package L includes: Installation check Supervision Commissioning Maintenance Energy Solutions WiloCare Premium Wilo-Live Assistant Optional add-on services: System Optimisation Repairs Extended Warranty
	Service Package M Norm-/SCP pumps	2219669
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package M includes: Installation check Supervision Commissioning Maintenance WiloCare Comfort Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Repairs Extended Warranty
	Service Package S Norm-/SCP pumps	2219640
	The Wilo service offers predefined service packages in three sizes to make it easier to combine individual services. The Wilo-Service package S includes: Installation check Commissioning Maintenance WiloCare Basic Wilo-Live Assistant Optional add-on services: System Optimisation Energy Solutions Supervision Repairs Extended Warranty
Extended Warranty	Extended Warranty Norm-/SCP pumps	2219591
	In combination of a new pump or system Wilo offers an extended warranty of up to five years in combination with commissioning and maintenance by the Wilo Service. Extended warranty includes: Full protection and predictable cost security Regular maintenance work by the Wilo Service
Installation	Installation Norm-/SCP pumps	2219357
	The Wilo service offers installation of our pumps or pumping systems. We offer an end-to-end process from gathering information on site to installing our product in the overall plant. An optimal installation set-up and the interaction of various individual factors lay the foundation for long-term operational safety. Installation includes: Professional inspection Provision of components/materials from Wilo and third-party suppliers Installation of pipelines and electronics Test runs
System Optimisation	System Optimisation Norm-/SCP pumps	2219252
	The Wilo Service offers proactive system optimisation by optimising settings and doing minor adjustments to ensure operational reliability. System Optimisation includes among others: Overhaul of pumps/systems to restore full performance Addition of new technologies or functions in older systems to save on capital expenditures (retrofitting)
Energy Solutions	Energy Solutions Norm-/SCP pumps	2219287
	Wilo Service offers a proactive support to point out possible energy savings. Our service creates an overview of all installed assets to show how the energy consumption of pumps or systems can be reduced. We offer targeted consultancy and analysis, including the involvement of subsidies as well as comprehensive support around the changeover to high-efficiency technologies. Wilo-Energy solution includes: Detailed assessment of the life cycle costs (LCC analysis) Energy audit including information about energy saving potential Proactive recommendation of replacement options Improving the environmental performance of your system Support in the changeover to Wilo high-efficiency pumps
Repair	Repair Norm-/SCP pumps	2219611
	Wilo Service draws on their competence and experience while consulting on site to decide whether the pump can actually be repaired on site or has to be sent in for a factory repair. Wilo also provides spare parts or a replacement pump to restore the operational reliability of the system. Repair includes: Verification and elimination of error causes by experienced Wilo experts Non-binding estimate for repairs Electric-hydraulic test run to ensure correct data regarding functionality, quality and performance of the pump or system Coating of various pump or system components for an optimised efficiency factor Use of genuine spare parts only Documentation of the repair in the service report

Atmos GIGA-N 100/250-15/4

Atmos GIGA-N 100/250-15/4

Installation and operating instructions

Wilo-Atmos GIGA-N

Certification booklet

Wilo-Atmos GIGA-N, Wilo-Yonos GIGA-N

Group Statement

Group Statement REACH

Continuous, infinitely variable control, differential pressure-sensitive CC-HVAC system (27)

CC-HVAC system

CC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

DDG (4-20mA)

DDG (4-20mA)

DDG transducer

DDG transducer

DDG power supply unit

DDG power supply unit

PTC thermistor tripping unit

PTC thermistor tripping unit

Continuous, infinitely variable control, temperature-dependent CC-HVAC system (21)

CC-HVAC system

CC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

BMS base module

BMS base module

CC communication module BACnet

CC communication module BACnet

Communication module LON

Communication module LON

Communication module ModBus

Communication module ModBus

Communication module GSM

Communication module GSM

Pump signalling module

Pump signalling module

Signal converter retrofit kit

Signal converter retrofit kit

Temperature module

Temperature module

Connection cable control modules/signalling modules

Connection cable control modules/signalling modules

PTC thermistor tripping unit

PTC thermistor tripping unit

Continuous, infinitely variable control, differential pressure-sensitive SC-HVAC system (35)

SC/SC-FC-HVAC system

SC/SC-FC-HVAC system

Antenna GSM/GPRS

Antenna GSM/GPRS

Outdoor temperature sensor Pt 100

Outdoor temperature sensor Pt 100

DDG impulse selector

DDG impulse selector

Communication module LON (SC)

Communication module LON (SC)

SC communication module BACnet