DrainLift WS 40-50

Plastic chamber with pipework, for connecting one or two pumps. Suitable for underground installation or building installation.

• As a lifting unit within buildings (above ground installation).
• As a pump chamber outside buildings (concealed floor installation).
• For backflow resistant drainage of
  • Drainage points below the backflow level
  • Drainage points that cannot be drained via the natural downward slope.

• Gate valve
• Surface coupling with integrated non-return valve

• Vessel volume: 255 l/67 US.liq.gal. (WS...E)/400 l/105 US.liq.gal. (WS...D)
• Maximum pressure in the discharge pipeline: 1.5 bar (22 psi)
• Discharge port: R 1½ (WS 40), R 2 (WS 50)
• Inlet connection: DN 100/150/200
• Ventilation connection: 75 mm (3 in)
• Fluid temperature: 3 ... +40 °C (37 ... 104 °F)
• Ambient temperature max.: 3 ... 40 °C (37 ... 104 °F)

• Pump chamber: PE
• Pipework: 1.4404 (AISI 316L)
• Stopcock: Red brass
• Non-return valve: PUR

Chamber

Pump chamber with optimised geometry for deposit-free operation. Chamber component with finning for high inherent stability and anti-buoyancy. The inlets are freely configurable. Two lifting eyes are integrated for attaching the lifting accessory. The upward curved pump chamber cover can be walked on and can be loaded with max. 200 kg. For the building installation, the pump chamber is equipped with a floor fixation.

Pipework

• Discharge pipe with flange connection on the pump side
• Gate valve
• Surface coupling
• Non-return ball valve (integrated in the surface coupling)

• Plastic chamber with installed pipework
  • Pipework with gate valve and surface coupling with integrated non-return valve
• Chamber cover with gasket
• HT double socket 50 mm (2 in) for drain connection
• Inlet set with hole saw 124 mm (5 in) and gasket DN 100
• Floor fixation
• Installation and operating instructions

• The pump chamber for two pumps has separate pipework for each pump. They therefore also have two discharge ports. Provide the Y-piece on-site.
• The maximum ground water level above the bottom edge of the chamber is 500 mm.

• Vessel volume: 255 l/67 US.liq.gal. (WS...E)/400 l/105 US.liq.gal. (WS...D)
• Maximum pressure in the discharge pipeline: 1.5 bar (22 psi)
• Discharge port: R 1½ (WS 40), R 2 (WS 50)
• Inlet connection: DN 100/150/200
• Ventilation connection: 75 mm (3 in)
• Fluid temperature: 3 ... +40 °C (37 ... 104 °F)
• Ambient temperature max.: 3 ... 40 °C (37 ... 104 °F)

• Pump chamber: PE
• Pipework: 1.4404 (AISI 316L)
• Stopcock: Red brass
• Non-return valve: PUR

Chamber

Pump chamber with optimised geometry for deposit-free operation. Chamber component with finning for high inherent stability and anti-buoyancy. The inlets are freely configurable. Two lifting eyes are integrated for attaching the lifting accessory. The upward curved pump chamber cover can be walked on and can be loaded with max. 200 kg. For the building installation, the pump chamber is equipped with a floor fixation.

Pipework

• Discharge pipe with flange connection on the pump side
• Gate valve
• Surface coupling
• Non-return ball valve (integrated in the surface coupling)

• Plastic chamber with installed pipework
  • Pipework with gate valve and surface coupling with integrated non-return valve
• Chamber cover with gasket
• HT double socket 50 mm (2 in) for drain connection
• Inlet set with hole saw 124 mm (5 in) and gasket DN 100
• Floor fixation
• Installation and operating instructions

• The pump chamber for two pumps has separate pipework for each pump. They therefore also have two discharge ports. Provide the Y-piece on-site.
• The maximum ground water level above the bottom edge of the chamber is 500 mm.