CronoLine IL-E 100/315-22/4-R1
| Hydraulic data | |
|---|---|
| Minimum efficiency index (MEI) | ≥0.4 |
| Maximum operating pressure PN | 16 bar |
| Note on dimensioning | 16 bar to 120 °C, 13 bar to 140 °C |
| Min. fluid temperature Tmin | -20 °C |
| Max. fluid temperature Tmax | 140 °C |
| Min. ambient temperature Tmin | 0 °C |
| Max. ambient temperature Tmax | 40 °C |
| Drive | |
|---|---|
| Mains connection | 3~400 V, 50/60 Hz |
| Number of poles | 4 |
| Motor efficiency class | IE4 |
| Power consumption P1 max | 24.00 kW |
| Rated power P2 | 22 kW |
| Max current Imax | 37.6 A |
| Emitted interference | EN 61800-3 |
| Interference resistance | EN 61800-3 |
| Insulation class | F |
| Protection class motor | IP55 |
| Motor protection | PTC integrated |
| Materials | |
|---|---|
| Pump housing | 5.1301/EN-GJL-250 KTL-coated |
| Impeller | Grey cast iron |
| Shaft | Stainless steel |
| Shaft seal | AQ1EGG |
| Lantern | 5.1301/EN-GJL-250 KTL-coated |
| Approved liquids (other liquids upon request) | |
|---|---|
| Heating water (as per VDI 2035) | yes |
| Heat carrier oil | Special version at additional charge |
| Cooling and cold water circulation systems | yes |
| Water-glycol mixtures (at 20 – 40 vol. % glycol and fluid temperature ≤ 40 °C) | yes |
| Installation dimensions | |
|---|---|
| Port-to-port length L0 | 700 mm |
| Pipe connection on the suction side DNs | DN 100 |
| Pipe connection on the discharge side DNd | DN 100 |
IL-E 100/315-22/4-R1
| L1, L2, L3: | Mains connection: 3~440 V ±10%, 50/60 Hz; 3~400 V ±10%, 50/60 Hz; 3~380 V -5%/+10%, 50/60 Hz |
| PE: | Protective conductor connection |
| DDG: | Connection for differential pressure sensor |
| In1 (1): | Actual value input 0-10 V/0-20 mA; 2-10 V/4-20 mA |
| GND (2): | Ground connection for In1 and In2 |
| + 24 V (3): | DC voltage output for an external consumer/sensor. Max load 60 mA |
| In2: | Setpoint input 0-10 V/0-20 mA; 2-10 V/4-20 mA |
| MP: | Multi-pump, interface for dual pump management |
| Ext. off: | Control input “Overriding Off”The pump can be switched on or off via an external, potential-free contact (24 V DC/10 mA). |
| SBM:* | Potential-free collective run signal (changeover contact according to VDI 3814) |
| SSM:* | Potential-free collective fault signal (changeover contact according to VDI 3814) |
| aux: | External pump cycling (only with dual pump operation). Pump cycling can be performed using an external, potential-free contact (24 VDC/10 mA) |
| DIP switch: | 1: Switchover between operation (O) and service mode (S)2: Activate/deactivate the menu for access disable |
| Optional: | IF-Modules for connection to the building automation |
| * Load capacity of contacts for SBM and SSM: min.: 12 V DC/10 mA max.: 250 V AC/1 A | |
| Product data | |
|---|---|
| Brand | Wilo |
| Product description | CronoLine IL-E 100/315-22/4-R1 |
| Article number | 2221280 |
| EAN number | 4062679238647 |
| Colour | Green |
| Minimum order quantity | 1 |
| Date of sales availability | 2023-06-30 |
| Packaging | |
|---|---|
| Packaging type | Euro pallet |
| Packaging property | Transport packaging |
| Pieces per pallet | 1 |
| Number per layer | 1 |
| Dimension, weight | |
|---|---|
| Length with packaging | 1200 mm |
| Length L | 1041 mm |
| Height with packaging | 1200 mm |
| Height H | 833 mm |
| Width with packaging | 800 mm |
| Width W | 468 mm |
| Gross weight, approx. m | 409 kg |
| Net weight, approx. m | 359 kg |
Glanded centrifugal pump with in-line design for pipe installation with built-in frequency converter for electronic control for constant or variable differential pressure (dp-c/dp-v).
Design:
- Single-stage low-pressure centrifugal pump
- Spiral housing in in-line design (suction and discharge ports with the same flanges in one line), flanges PN 16 – drilled acc. to EN 1092-2
- Pressure measuring connections (R 1/8) for mounted differential pressure sensor (version ...-R1 without differential pressure sensor)
- Pump housing and motor flange with cataphoretic coating as standard.
- Mechanical seal for pumping water up to Tmax. = +140 °C. A glycol admixture of 20 % to +40 % by volume is permitted up to T ≤ +40 °C. An alternative mechanical seal must be provided in water-glycol mixtures with glycol proportions > 40 % up to max. 50 % by volume and a fluid temperature of > +40 °C up to max. +120 °C or fluids other than water. When using water-glycol mixtures, the use of an S1 variant with a corresponding mechanical seal is generally recommended.
Accessories:
- Mounting brackets for fixing to the foundation
- IR-Stick
- IF module PLR
- IF module LON
- IF module Modbus
- IF module BACnet
- IF module CAN
- Control systems VR-HVAC/CCe-HVAC/SCe-HVAC
- Differential pressure sensor (DDG) sets 0-10 V for pumps in version ...-R1
Standard equipment:
- One-button manual operation level for:
- Pump On/Off
- Setpoint and speed adjustment
- Selecting the control mode: Δp-c (constant differential pressure), Δp-v (variable differential pressure), PID controller, n-constant (constant speed)
- Selection of operating mode in dual-pump operation (main/standby operation, parallel operation)
- Configuration of operating parameters
- Fault acknowledgement
- Pump display for indication of:
- Control mode
- Setpoint (e.g. differential pressure or speed)
- Error and warning messages
- Actual values (e.g. power consumption, actual value of the sensor)
- Operating data (e.g. operating hours, energy consumption)
- Status data (e.g. status of SSM and SBM relay)
- Device data (e.g. pump name)
Additional functions:
- Interfaces: Control input “Overriding Off”, “External pump cycling” (effective only in dual-pump operation), analogue input 0–10 V, 2–10 V, 0–20 mA, 4–20 mA for constant speed (DDC) or for remote setpoint adjustment, analogue input 0–10 V, 2–10 V, 0–20 mA, 4–20 mA for actual value signal of the pressure sensor, infrared interface for wireless communication with the operating and service device Wilo-IR-Stick, slot for Wilo IF modules for connecting to the building automation, configurable, potential-free fault and operating/ready message, interface for dual-pump communication
- Three-phase AC motor with frequency converter
- Integrated dual-pump management
- Adjustable time interval for pump cycling (in dual-pump operation)
- Integrated full motor protection
- Different operating modes for heating (HV) or air-conditioning (AC) applications
- Access disable
- Different operation levels: Standard/service
| Operating Data | |
|---|---|
| Min. fluid temperature Tmin | -20 °C |
| Max. fluid temperature Tmax | 140 °C |
| Min. ambient temperature Tmin | 0 °C |
| Max. ambient temperature Tmax | 40 °C |
| Maximum operating pressure PN | 16 bar |
| Note on dimensioning | 16 bar to 120 °C, 13 bar to 140 °C |
| Minimum efficiency index (MEI) | ≥0.4 |
| Drive | |
|---|---|
| Mains connection | 3~400 V, 50/60 Hz |
| Motor efficiency class | IE4 |
| Power consumption P1 max | 24000 W |
| Rated power P2 | 22 kW |
| Max current Imax | 37.6 A |
| Max. speed nmax | 1480 1/min |
| Emitted interference | EN 61800-3 |
| Interference resistance | EN 61800-3 |
| Insulation class | F |
| Protection class motor | IP55 |
| Motor protection | PTC integrated |
| Materials | |
|---|---|
| Pump housing | 5.1301/EN-GJL-250 KTL-coated |
| Impeller | Grey cast iron |
| Shaft | Stainless steel |
| Shaft seal | AQ1EGG |
| Lantern | 5.1301/EN-GJL-250 KTL-coated |
| Installation dimensions | |
|---|---|
| Pipe connection on the suction side DNs | DN 100 |
| Pipe connection on the discharge side DNd | DN 100 |
| Port-to-port length L0 | 700 mm |
| Ordering information | |
|---|---|
| Brand | Wilo |
| Product description | CronoLine IL-E 100/315-22/4-R1 |
| Net weight, approx. m | 359 kg |
| Article number | 2221280 |
Installation and operating instructions
Wilo-CronoLine-IL-E (11-22 kW), Wilo-CronoTwin-DL-E (11-22 kW), Wilo-CronoBloc-BL-E (1,5-22 kW)
| Article Number | 2234255 |
| Edition | 2024-02 |
| Number of pages | 88 |
| Language | en |
PDF (13 MB)Wilo-CronoLine-IL-E (11-22 kW), Wilo-CronoTwin-DL-E (11-22 kW), Wilo-CronoBloc-BL-E (1,5-22 kW)
| Article Number | 2234256 |
| Edition | 2024-02 |
| Number of pages | 328 |
| Language | de, en, fr, nl |
PDF (21 MB)Group Statement
Group Statement REACH
| Edition | 2021-05 |
| Number of pages | 5 |
| Language | language neutral |
PDF (327 KB)Continuous, infinitely variable control, differential pressure-sensitive CCe-HVAC system (29) | |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 3 x 22.0 | 2536726 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 5 x 22.0 | 2536728 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 10 m cable | 2533863 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery
| |||
Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery
| |||
additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery
| |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 100 Signal Trans.(4-20mA) | 2211740 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 20 Signal Trans.(4-20mA)2G VP. | 2136456 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 40 Signal Trans.(4-20mA)2G VP. | 2136458 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable:
Scope of delivery
| |||
Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery
| |||
Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection:
Pipework connection:
Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications | |||
Continuous, infinitely variable control, temperature-dependent CCe-HVAC system (22) | |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 3 x 22.0 | 2536726 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 5 x 22.0 | 2536728 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 10 m cable | 2533863 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery
| |||
The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery
| |||
additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology.
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology.
| |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Continuous, infinitely variable control, differential pressure-sensitive SCe-HVAC system (23) | |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 2x49A-WM | 2545279 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 3x49A-WM | 2545280 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 10 m cable | 2533863 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery
| |||
Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery
| |||
Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery
| |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 100 Signal Trans.(4-20mA) | 2211740 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 20 Signal Trans.(4-20mA)2G VP. | 2136456 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 40 Signal Trans.(4-20mA)2G VP. | 2136458 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable:
Scope of delivery
| |||
Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery
| |||
Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection:
Pipework connection:
Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications | |||
Continuous, infinitely variable control, temperature-dependent SCe-HVAC system (14) | |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 2x49A-WM | 2545279 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 3x49A-WM | 2545280 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 10 m cable | 2533863 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery
| |||
The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery
| |||
Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery
| |||
Pipe installation, adapter fitting (3) | |||
The Wilo-F flange intermediate connecting pieces are used for compensation of the port-to-port length in case of a pump replacement. They are made of grey cast iron and are provided for length compensation of flange connections. The washers included in the scope of delivery must be used for pumps that have combination flanges. Scope of delivery
| |||
Intermediate flange pieces F 35, DN 100x55mm, PN 10/16 | 110862695 | ||
The Wilo-F flange intermediate connecting pieces are used for compensation of the port-to-port length in case of a pump replacement. They are made of grey cast iron and are provided for length compensation of flange connections. The washers included in the scope of delivery must be used for pumps that have combination flanges. Scope of delivery
| |||
The Wilo-F flange intermediate connecting pieces are used for compensation of the port-to-port length in case of a pump replacement. They are made of stainless steel and are provided for length compensation of flange connections also in domestic hot water circulation systems. The washers included in the scope of delivery must be used for pumps that have combination flanges. Scope of delivery
| |||
Wall fixation/installation on a base (1) | |||
Mounting brackets for the installation on a base of in-line and monobloc pumps. Comprised of several angle brackets (number dependent on the pump type), intended for the screwed connection with the screw-on bases or feet of the pump. The angle brackets ensure secure fastening of the pump to the foundation. Including fixation material. Notice The mounting brackets / angle brackets must be lined by the dimension specified for the following pump types:
Scope of delivery
| |||
Pump control/accessories (25) | |||
Dualband-Rundstrahlantenne mit FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 10 m cable | 2533863 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
D-network tri-band antenna 15 m cable | 2533864 | ||
Triband-Rundstrahlantenne mit Montagebügel und FME-Buchse zur Montage am Schaltschrank. Zubehör für die Schaltgeräte Control SC.../SCe.../CC.../CCe... in Verbindung mit GSM/GPRS-Modul. | |||
Koaxialer Steckverbinder SMA-Stecker auf FME-Stecker in kompakten Bauform mit Schraubverschluss. Einsetzbar bis 2 GHz, der Wellenwiderstand beträgt 50 Ω. | |||
The BMS base module is required as a connection element with the CPU when using the options of signalling modules or control modules. Can be used in conjunction with switchgears of the CC/CCe-HVAC system or the CC/CCe-HVAC Booster system. Each CC/CCe switchgear requires only one base module. Order in connection with switchgear required, not for retroactive installation. Version: Series module in a plastic housing with LEDs to display the state of the inputs and outputs, fixation on a 35 mm DIN rail. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MS/TP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IMS/TP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-CC/CCe-HVAC system and CC/CCe booster for communication in BACnet networks. The BACnet IP communications module is an extension for integrating a CC/CCe system as a slave in an already existing BACnet building automation system. The connection of the BACnet IP module is via the RJ45 interface. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet IP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection 2xRJ45 and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the BACnet IP communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Interface expansion of the CC/CCe-HVAC or CC/CCe Booster system. Version Plug-in cartridge for installation in the CPU for connecting the CCe switchgear to communication systems (GSM, Modbus, Webserver, LON, etc.), if no frequency converter is installed. Retroactive installation of the CC communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC switchgear series and the CC/CCe booster system. For selection and communication in GSM wireless telephone networks. The GSM module represents an extension of the CC system for the transfer of status and fault signals of a CC/CCe system via SMS (Short Message Service). Up to 4 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the CC/CCe system. Version Insulant housing for switch cabinet installation, fastening by means of the accessory kit supplied (adapter plate). An SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m and 15 m are available as additional accessories. SIM cards are to be provided on-site (available from various mobile telephone providers). Retroactive installation of the GSM module is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Additional module for equipping the switchgear series Wilo-SC/SCe-HVAC, SC/SCe-Booster and SC-L for dialling into and communicating in GSM mobile phone networks. The GSM module represents an extension of the SC/SCe system for the transfer of status and fault signals of a SC/SCe system via SMS (Short Message Service). Up to 2 recipients can be set up and prioritised who are to receive a fault signal via SMS in the event of a system failure. The settings with respect to the SMS functions can be made directly on the display of the SC/SCe system. Version: Insulant housing for installation in a switch cabinet, fixation by means of the supplied accessories kit (adapter plate). A SIM card and an antenna are required for the operation of the modem which are not included in the scope of delivery. Antennas with various cable lengths of 2.5 m, 10 m, 15 m are available as additional accessories. SIM cards are available from various mobile telephone providers. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the communication module is possible. The installation must be performed by customer service, as a software update of the SC/SCe system is also required. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in LON networks. The LON communications module represents an extension to the integration of a CC/CCe system as a participant in the already existing LON building management system. The connection of the LON module is through the LON connector. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the LON communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
The SC-OPTION LON communications module represents an extension to the integration of an SC/SCe system as a participant in the already existing LON building management system. Certain parameters can be written and read via LON, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Retroactive installation of the LON module in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series and CC/CCe booster for communication in Modbus RTU networks. The Modbus RTU communications module represents an extension to the integration of a CC/CCe system as Modbus Slave in an already existing bus system of the building management system. The connection is made via an RS485 interface. The settings with respect to the interface configuration can be made on the display of the CC/CCe system. Certain parameters can be written and read via Modbus, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. Version Insulating housing for switch cabinet installation, with interface connection and diagnosis LEDs, fixation on 35 mm DIN rail. Retroactive installation of the Modbus RTU communications module in the switchgear is possible. The installation must be performed by Wilo Customer Service, as a software update of the CC/CCe system is also required. Scope of delivery
| |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Connection cable for connecting up to 4 control modules with the GLT base module. Can be used in conjunction with switchgears of the CC/CCe-HVAC system. The number of connection cables required for control modules/signalling modules per CC(CCe switchgear is always 1. | |||
Additional module for the equipment of the Wilo-CC/CCe/SC/SCe-HVAC system switchgear series and for the CC/CCe/SC/SCe Booster for signal selection (minimum value) of two to eight measurement points for index circuit evaluation. The DDG impulse selector outputs the signal with the smallest value (minimum value) from a minimum of 2 to a maximum of 8 input signals 0(4)-20 mA. If several sensors are used on-site, then the most minimal of the values can be determined with the aid of the DDG impulse selector. Version Impulse selector for installation in a switch cabinet, channel selection with DIP switches accessible from the front, LED operation and output signal, galvanic separation between measurement signal and supply voltage, fixation on 35 mm DIN rail. Retroactive installation of the DDD impulse selector in the switchgear is possible. Installation by Wilo Customer Service is recommended. Scope of delivery
| |||
Temperature sensor for equipping the Wilo-VR/CC/CCe/Sc/SCe system switchgear series when using the temperature-dependent control modes. The housing should not be exposed to direct sunlight. Version Insulant housing made of fibreglass-reinforced polycarbonate, greyish similar to RAL 7035. Fixation with two to four screws of 4 mm (not included in the scope of delivery). Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. Version: Relay module with operating status LED's, secured on 35 mm DIN rail Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series for outputting individual operation and fault signals via potential-free relay contacts (changeover contacts) such as:
in conjunction with the base module GLT and the connection cable signalling modules. The signalling module pump 3-6 can be used only in connection with signalling module 1-2. Version: Relay module with operating status LED's, secured on 35mm DIN rail Scope of delivery
| |||
For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe-Booster and Wilo-SiBoost Smart with BACnet-MSTP networks. The SC-OPTION BACnet MSTP communications module represents a software extension for the integration of an SC/SCe system as a slave in the already existing BACnet building management system. The connection of the BACnet MS/TP module to the RS485 bus proceeds via Twisted-Pair cabling/wiring. BACnet (Building Automation and Control Networks) ensures interoperability between devices from different manufacturers. Certain parameters can be written and read via BACnet MSTP, e.g. switchgear data, status and mode of the pumps, current actual value, setpoints, current speed of the pumps, recorded temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. A retroactive activation of the "BACnet MSTP" function in the switchgear is possible. Execution by Wilo Customer Service is recommended. Scope of delivery
| |||
For connecting Wilo-Smart-SC/SCe-HVAC systems, Wilo-Smart-SC/SCe booster with BACnet IP networks. The communication module SC-OPTION BACnet IP is a hardware extension and optionally a software extension to connect an SC/SCe system as a participant in an existing BACnet IP building automation. The connection of the BACnet IP module to the RS485 bus takes place via twisted-pair cabling. BACnet (Building Automation and Control Networks) IP ensures interoperability between devices from different manufacturers. With BACnet IP, different parameters can be read and written, e.g. switchgear data, pump status and modes, actual values, setpoints, the current speed of the pump, measured temperatures, operating hours, switching cycles, etc. The module is installed in the switchgear by the manufacturer when the order for the system is received. Only Wilo customer service can perform a subsequent activation and installation of the BACnet IP function in the switchgear. Scope of delivery
| |||
Relay output module for outputting individual operation and fault signals for pumps 1 to 4, frequency converter and low water fault signal. Suitable for the use in connection with SC/SCe-HVAC system and SC/SCe booster. Scope of delivery
| |||
additional module for the equipment of the Wilo-CC/CCe/SC/SCe system switchgear series and CC/CCe/SC/SCe-Booster for converting 2-10 V signals in 4-20 mA signals. The signal converter converts the 2-10 V input signal into a 4-20 mA output signal. If sensors with 2-10 V outputs are used on-site, then CC/CCe or SC/SCe systems can process this signal only in connection with the signal converter, as this converts the signal of the sensor into 4-20 mA. Version Impulse selector for switch cabinet installation in plastic housing, single-channel 3-way isolating amplifier, input, voltage, norm signal, output current norm signal, operating display. Input value = output value, e.g. input 0-10 V for output 0-20 mA or input 2-10 V for output 4-20 mA. Input, output and supply are galvanically isolated, 3-way isolator, LED run signal, secured on 35 mm DIN rail. A retroactive installation of the signal converter is possible. It is recommended to have installation carried out by the Wilo customer service. Scope of delivery
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. The temperature module for CC-HVAC systems with 4 – 6 pumps can be used only in connection with a temperature module for systems with 1 – 3 pumps. In CCe-HVAC systems this temperature module is suitable for 1 – 6 pumps. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology.
| |||
Additional module for equipping the Wilo-CC/CCe-HVAC system switchgear series when using the temperature-dependent control modes. An address modules is also supplied for complying with hardware-side addressing. Version: Module to be arranged on a 35 mm DIN rail with four channels in order to detect temperature sensors which have to be provided by the customer (PT100/PT1000) in 2 or 3-wire technology.
| |||
Pump control/Comfort control system (4) | |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 3 x 22.0 | 2536726 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
CCe-HVAC system 5 x 22.0 | 2536728 | ||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Wilo-Comfort Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Completely electronic Comfort-Controller (CCe) in the sheet metal enclosure (colour: pebble grey), completely wired. Switchgear suitable for connection to 3/PE 400V/50 Hz three phase nets in accordance with IEC 60038 (other voltages on request), comprised of internal power supply, CPU, backup battery, analogue/digital modules, power pack with fuses, contactors and motor protection devices. Fully graphics-capable touch screen with 3-colour backlight for indicating the operating status operation/ fault/ acknowledged fault, and supporting symbols and plain text for menu navigation in up to 27 languages, with European and Asiatic characters. 3 user levels, display and selection of menu language, passwords, operating parameters, elapsed time indicator (individual and total operating hours), history memory for operating and error messages with time stamp via real time clock, pump status and control variable actual value display, actual pressure display, diagram function, main switch, internal revision switch, Manual-0-Automatic for each pump. Operating mode selection Manual-0-Automatic for each pump via Touch panel, potential-free contacts for collective SBM/SSM run and fault signals (changeover contact) as well as ON/OFF connection for external systems (on-site potential-free NC contact), input 0/4-20 mA for external setpoint adjustment. Overload protection via TWC, motor protection via motor protection switch, starting from 5.5 kW thermal overload relay. Digital inputs for alarm signals, e.g. anti-frost protection (on-site potential-free NC contact), PID controller, automatic pump cycling and running time optimisation with multi-pump systems. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the following, programmable control variables:
Three setpoints are selectable by default. Automatic fault-actuated switchover on idle pump(s). Short test run of pump(s) during standstill, pilot pump function. Option for live-zero evaluation for conductivity test (sensor/setpoint input), select from:
Extra charge for optional modules (installation in factory or later after technical clarification):
Ordering example: Wilo CCe-HVAC 4x5.5 WM: Switchgear for 4 pumps with P2=5.5 kW in version as switch cabinet for wall fixation. Scope of delivery
| |||
Pump control/Smart control system (4) | |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 2x49A-WM | 2545279 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
SCe-HVAC system 3x49A-WM | 2545280 | ||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Wilo-Smart Controller for digital, stepless power control of one-pump and multi-pump systems in heating, air-conditioning and ventilation applications. For infinitely variable, electronically controlled pumps or pumps with integrated frequency converter. Hardware Fully electronic Wilo-Smart Controller (SCe) in steel sheeting enclosure (colour: pebble grey), comprised of internal power supply, microprocessor with “Soft-SPS”, analogue and digital inputs and outputs, LCD display (backlit) for displaying operating data, control parameters, operating states of the pumps, error messages and history memory. LEDs for display of system status (operation/fault), setting of operating parameters and acknowledgement of fault messages via Green Button Technology, lockable main switch, potential-free contacts for SBM/SSM collective operation and collective fault signals, contacts for external On/Off and 2nd setpoint, conductivity test in the sensor cable. The pump mains power feed is protected via the circuit breaker. Actual value output via a 0-10 V analogue signal for external measurement / display applications, (10 Volt depending on the sensor end value). External remote setpoint adjustment via 4...20 mA signal. Automatic, load-sensitive cut-in of 1 to n peak-load pump(s) depending on the control variables:
Software functions Fully automatic control for 1 to n pumps (frequency-controlled) by means of setpoint/actual value comparison, 4-20 mA sensor signal (conductivity test) for control variable actual values, menu navigation with symbols and menu numbers. 2 parameter sets can be selected: Easy Menu (setpoint & control mode) or expert Menu (operation and control parameters) Can be selected by Customer Service with or without standby pump, automatic switching of an operating pump to the reserve pump in the event of a fault, operating mode of the pumps can be selected freely (manual, off, automatic), elapsed time indicator for each pump and system, switching cycle counter for each pump and system. Monitoring of Max. and Min. values of the system with adjustable delay times and limits, external On/Off via contact for deactivation of the Automatic mode of the system, fault memory of the last 16 faults, setpoint switching of 2nd setpoint can be activated by contact, SBM and SSM logic reversal possible, parameters pre-set at the factory for simple commissioning. Automatic, configurable pump cycling
Automatic pump trial run (pump kick)
Standards followed
Extra charge for optional modules for connection to BMS and bus systems (installation at the factory or subsequently after technical clarification):
Scope of delivery
| |||
Pump control/interface module (6) | |||
Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. Additional functions Serial, digital interface for connection to BA building automation via interface converter or company-specific coupling modules for the transfer of data points as:
Equipment TP-FT 10 interface with LonTalk protocol Scope of delivery
Information about the download http://www.wilo.de/automation | |||
IF module PLR | 2035069 | ||
Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. Additional functions Serial, digital interface for connection to BA building automation via interface converter or company-specific coupling modules for the transfer of data points as:
Equipment PLR interface (WILO) Scope of delivery
| |||
IF module CANopen | 2085044 | ||
Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. Additional functions Serial, digital interface for connection to BA building automation via interface converter or company-specific coupling modules for the transfer of data points as:
Equipment CAN 2.0A interface with CANopen protocol Scope of delivery
Information about the download http://www.wilo.de/automation | |||
IF module Modbus RTU | 2097809 | ||
Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. Additional functions Serial, digital interface for connection to BA building automation via interface converter or company-specific coupling modules for the transfer of data points as:
Equipment RS485 interface with Modbus RTU protocol Scope of delivery
Information about the download http://www.wilo.de/automation | |||
Interface modules as retrofittable plug-in modules for extending the communication interfaces of the pump in accordance with various standards and protocol variants according to type key. Additional functions Serial, digital interface for connection to BA building automation via interface converter or company-specific coupling modules for the transfer of data points as:
Equipment RS485 interface with BACnet MS/TP protocol Scope of delivery
Information about the download http://www.wilo.de/automation | |||
Interface module as retrofittable plug-in module for adding Wilo-Smart Connect functions to the pump. Interface equipment
Functions Bluetooth connection to Wilo-Assistant App
Optional Wilo Net connection to Wilo-Smart Gateway – remote monitoring of pump operation via the Wilo-Smart Cloud
Optional connection to the Wilo-Smart temperature sensor kit Two additional temperature sensor values to complete the process chart, can be monitored via Bluetooth and Wilo-Smart Cloud Scope of delivery
| |||
Differential pressure detection (9) | |||
Signal transmitter for differential pressure-sensitive variable speed control. For direct connection with the pump (installation in the piping for Yonos GIGA-N). Control modes dp-c and dp-v (dp-v not possible with Yonos GIGA-N). Suitable for pump version …-R1. Scope of delivery
| |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 20 Signal Trans.(4-20mA)2G VP. | 2136456 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 40 Signal Trans.(4-20mA)2G VP. | 2136458 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Wilo-DDG 60 Signal Trans.(4-20mA)2G VP. | 2136460 | ||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Signal transmitter with fixation elements for differential pressure-sensitive variable speed control. With 5 m connection cable for connection to the switchgear; larger distances should be extended on-site:
Notice: not applicable with VR-HVAC Scope of delivery
| |||
Power supply unit (for wall fixation) for the power supply to the signal transmitter DDG (differential pressure sensor) in conjunction with the DDG impulse selector. Scope of delivery
| |||
DDG transducer. Amplifier (for wall fixation) for amplifying signals from the DDG signal transmitter for cable lengths in excess of 250 m, including power supply unit DDG (24 V). Signal cable:
Scope of delivery
| |||
Differential pressure sensor extension kit for hose pipe applications Depending on the installation situation in a hose pipe application, the length of the existing copper spiral is not enough to reach the pressure measurement connections of the shared pipe (only then can the differential pressure be measured properly). The differential pressure sensor extension kit for hose pipe applications serves to extend the differential pressure sensor kit of the pump comfortably to the pressure measurement connections in the pipe. The kit contains the necessary accessories to make the connections on the differential pressure sensor side and the pipe network side. Scope of delivery Differential pressure sensor-side connection:
Pipework connection:
Ordering information Make: Wilo Type: Differential pressure sensor extension kit for hose pipe applications | |||
Operating/service units (1) | |||
USB stick for wireless data exchange for all electronically controlled Wilo pumps with infra-red interface; can be adapted to any commercially-available Windows PCs/laptops with USB interface. The IR-Stick in combination with the supplied Wilo software (CD-ROM), makes it possible to read out and save data records for pumps as well as send previously defined pump settings. IR carrier frequency: 33 kHz / 455 kHz Software upgrade: via USB Particularly suitable for:
PC minimum requirements Interfaces: USB 1.1 connection (USB 2.x / 3.x compatible) Operating system: Windows 2000, Windows XP, Vista, Windows 7 Display: Min. XGA (1024 x 768 pixels) Scope of delivery
The current firmware for the Wilo-IR-Stick along with the current operating software is available for downloading at www.wilo.com/accessories. | |||
With Wilo as your partner, you can not only be sure of choosing high-quality product solutions, but also of benefiting from a comprehensive, worry-free package of well thought-out services. We collaborate to develop a service concept tailored to your individual needs; with our expertise and personal consultancy, we make sure that the operation of your systems is as energy-efficient, reliable and economical as possible. All the while our competent Wilo service technicians are ready to assist you with fast, reliable and on-time support.
Recommended services | |||
 Wilo-Live Assistant | Wilo-Live Assistant Service | 2216415 | |
The Wilo-Live Assistant is a technical advisor at your side during pump service. By using the Wilo-Live Assistant, our expert advisers can support you in the boiler or equipment room via video transmission – live and in real time. You use your smartphone to show the installation set-up, while the Wilo expert follows everything on their screen. They can see the components as well as other details and can thus determine where the fault or breakdown originates. We prevent downtime and ensure operational reliability of your pumps and systems! The Wilo-Live Assistant includes:
| |||
 Supervision | Supervision Glanded pumps | 2219321 | |
Wilo supports during the concept phase to ensure quality work and cost efficiency. Our competent and qualified Wilo Service will support you with recommendations and technical advice throughout the entire project. Supervision includes:
| |||
 Commissioning | Commissioning Glanded pumps | 2219391 | |
For perfect functioning of the pump(s) / system(s), it is recommended to have the commissioning carried out by the works' own WILO SE Customer Service Department. Optimum setting and efficient operation of the system are ensured as a result. Commissioning is comprised of the following points:
The price for commissioning only applies to system(s) which have been installed in accordance with the installation and operating instructions and state-of-the-art technology. No costs for any materials which may be required are included. | |||
 Maintenance | Maintenance BASIC Glanded pumps | 2219531 | |
In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points:
Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. | |||
Maintenance COMFORT Glanded pumps | 2219493 | ||
In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points:
Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. | |||
Maintenance PREMIUM Glanded pumps | 2219546 | ||
In order to ensure and guarantee operational reliability of the pumps/systems, it is recommended to have regular and DIN-compliant inspections and maintenance carried out by the works' own WILO SE Customer Service Department. The tasks are carried out in accordance with DIN 31051 / DIN EN 13306. The tasks comprise the following points:
Scheduling and organisation is performed by WILO. Other individual maintenance offers are possible on request. | |||
More suitable services | |||
 Extended Warranty | Extended Warranty Glanded pumps | 2219590 | |
In combination of a new pump or system Wilo offers an extended warranty of up to five years in combination with commissioning and maintenance by the Wilo Service. Extended warranty includes:
| |||
 Installation | Installation Glanded pumps | 2219356 | |
The Wilo service offers installation of our pumps or pumping systems. We offer an end-to-end process from gathering information on site to installing our product in the overall plant. An optimal installation set-up and the interaction of various individual factors lay the foundation for long-term operational safety. Installation includes:
| |||
 System Optimisation | System Optimisation Glanded pumps | 2219251 | |
The Wilo Service offers proactive system optimisation by optimising settings and doing minor adjustments to ensure operational reliability. System Optimisation includes among others:
| |||
 Energy Solutions | Energy Solutions Glanded pumps | 2219240 | |
Wilo Service offers a proactive support to point out possible energy savings. Our service creates an overview of all installed assets to show how the energy consumption of pumps or systems can be reduced. We offer targeted consultancy and analysis, including the involvement of subsidies as well as comprehensive support around the changeover to high-efficiency technologies. Wilo-Energy solution includes:
| |||
 Repair | Repair Glanded pumps | 2219610 | |
Wilo Service draws on their competence and experience while consulting on site to decide whether the pump can actually be repaired on site or has to be sent in for a factory repair. Wilo also provides spare parts or a replacement pump to restore the operational reliability of the system. Repair includes:
| |||