Sewage lifting unit; Single-pump system | Existing pump | |
 | | |
Description | ||
Product description | DrainLift SANI-M.16/T540/4C-CEE | DrainLift SANI-M.16T/4C |
Article number | 6098862 | 2549922 |
Series | DrainLift SANI-M | DrainLift SANI-M |
Mains connection | 3~400 V ±10%, 50 Hz | 3~400 V ±10%, 50 Hz |
Data sheet
| Hydraulic data | |
|---|---|
| Maximum operating pressure PN | 4 bar |
| Max. permissible pressure in the pressure pipe P | 1.5 bar |
| Min. fluid temperature Tmin | 3 °C |
| Max. fluid temperature Tmax | 40 °C |
| Min. ambient temperature Tmin | 3 °C |
| Max. ambient temperature Tmax | 40 °C |
| Max. fluid temperature, for short periods up to 5 min. T | 65 °C |
| Sound-pressure level | 70 |
| Gross volume of the tank V | 99 l |
| Switching volume V | 50 l |
| Useable volume at 180 mm inlet height V | 50 l |
| Useable volume at 250 mm inlet height V | 63 l |
| Useable volume at 315 mm inlet height V | 74 l |
| Macerator | no |
| Free ball passage of the hydraulics | 44 mm |
| Motor data | |
|---|---|
| Mains connection | 3~400 V, 50 Hz |
| Rated current IN | 3.6 A |
| Protection class | IP68 |
| Phase | 3 |
| Rated speed n | 2850 1/min |
| Number of poles | 2 |
| Activation type | Direct On Line (DOL) |
| Max. switching frequency t | 60 rph |
| Power consumption P1(Q=max.) of selected impeller * number of pumps P1 | 2100 W |
| Operating mode per pump | S1 |
| Insulation class | F |
| Motor protection | Bimetall |
| Cable | |
|---|---|
| Connection cable length L | 10 m |
| Cable type | H07RN-F |
| Cable cross-section | 6G1 |
| Mains plug | CEE 16A, 3P+N+PE, 6h |
| Materials | |
|---|---|
| Tank | PE |
| Pump housing | PP-GF30 |
| Impeller | PP-GF30 |
| Shaft | Stainless steel |
| Gasket material | FKM |
| Motor housing | Stainless steel |
| Installation dimensions | |
|---|---|
| Diagonal dimension Diagonal axis | 850 mm |
| Pipe connection, suction side | DN/OD 40 (HT pipe) DN/OD 50 (HT pipe) DN/OD 63 (HT pipe) DN/OD 75 (HT pipe) DN/OD 90 (HT pipe) DN/OD 110 (HT pipe) DN/OD 160 (HT pipe) |
| Pipe connection, discharge side | DN 80 |
| Connection venting | DN/OD 75 (HT pipe) |
| Connection for drainage pipe | DN/OD 50 (HT pipe) |
Pump curves
Ordering information
| Product data | |
|---|---|
| Brand | Wilo |
| Product description | DrainLift SANI-M.16T/4C |
| Article number | 2549922 |
| EAN number | 4062679007083 |
| Colour | green/black |
| Minimum order quantity | 1 |
| Date of sales availability | 2020-07-06 |
| Successor model article number | 6098862 |
| Successor model designation | DrainLift SANI-M.16/T540/4C-CEE |
| Packaging | |
|---|---|
| Packaging type | Cardboard box |
| Packaging property | Transport packaging |
| Pieces per pallet | 1 |
| Number per layer | 1 |
| Dimension, weight | |
|---|---|
| Length with packaging | 720 mm |
| Length L | 700 mm |
| Height with packaging | 800 mm |
| Height H | 575 mm |
| Width with packaging | 620 mm |
| Width W | 600 mm |
| Gross weight, approx. m | 53 kg |
| Net weight, approx. m | 40 kg |
Ready for connection and fully submersible single-pump lifting unit for pumping aggressive fluids.
Fluid
For the collection and pumping of these fluids in commercial areas:
- Sewage with faeces
- Condensate from boilers
- Lake water and sea water
Max. NaCl content (salt water): 30 g/l until 20 °C - Swimming pool water, max. chloride content: 400 mg/l
- Wastewater, slightly acidic with a pH value >3.5
- Demineralised/cleaned water
Sewage pumping according to 12050
The lifting unit follows DIN EN 12050-1.
Construction
Gas- and watertight collection tank:
- Sloped floor at an angle
- Inspection opening with transparent cover
- Freely selectable inlets in the shown areas
- Level measurement with a level sensor 4 ... 20 mA
Sewage pump:
- Mounted directly on the collection tank
- Self-cooling motor (sheath flow cooling) with thermal motor monitoring
- Discharge port with non-return valve including inspection opening attached
Pre-wired "Control EC-L" switchgear for automatic operation:
- Operation through display and icon-based, alphanumeric menu
- Collective fault signal with potential-free contact
- Individual fault signal with potential-free contact
- ModBus interface
- Integrated and mains-independent alarm
- Adjustable follow-up time
Scope of delivery
- Lifting unit with switchgear and connection cable with plug
- Flange connector from DN 80, PN 10 to DN/OD 110
- Flexible collar DN/OD 110 for discharge connection
- HT double socket DN/OD 75 for ventilation connection
- HT double socket DN/OD 50 for drain connection
- Inlet set with hole saw 124 mm (5 in) and seal for HT pipe DN/OD 110
- Floor fixation set
- Noise insulation mat
- 9 V rechargeable battery
- Installation and operating instructions
| Operating data |
|---|
| Approved field of application | |
|---|---|
| Fluid temperature T | 3 °C |
| Max. fluid temperature, for short periods up to 5 min. T | 65 °C |
| Ambient temperature T | 3 °C |
| Maximum operating pressure PN | 4 bar |
| Max. permissible pressure in the pressure pipe P | 1.5 bar |
| Product data | |
|---|---|
| Gross volume of the tank V | 99 l |
| Useable volume at 180 mm inlet height V | 50 l |
| Useable volume at 250 mm inlet height V | 63 l |
| Useable volume at 315 mm inlet height V | 74 l |
| Sound-pressure level | 70 |
| Operating mode (non-immersed) | S1 |
| Height H | 575 mm |
| Length L | 700 mm |
| Width W | 600 mm |
| Diagonal dimension Diagonal axis | 850 mm |
| Free ball passage of the hydraulics | 44 mm |
| Motor data | |
|---|---|
| Mains connection | 3~400 V, 50 Hz |
| Voltage tolerance | ±10 % |
| Rated power P2 | 1.5 kW |
| Rated speed n | 2850 1/min |
| Rated current IN | 3.6 A |
| Insulation class | F |
| Protection class motor | IP68 |
| Activation type | Direct On Line (DOL) |
| Max. switching frequency t | 60 rph |
| Operating mode per pump | S1 |
| Motor protection | Bimetall |
| Cable | |
|---|---|
| Connection cable length L | 10 m |
| Cable type | H07RN-F |
| Cable cross-section | 6G1 |
| Mains plug | CEE 16A, 3P+N+PE, 6h |
| Materials | |
|---|---|
| Tank | PE |
| Pump housing | PP-GF30 |
| Impeller | PP-GF30 |
| Shaft | Stainless steel |
| Gasket material | FKM |
| Motor housing | Stainless steel |
| Installation dimensions | |
|---|---|
| Pipe connection, suction side | DN/OD 40 (HT pipe) DN/OD 50 (HT pipe) DN/OD 63 (HT pipe) DN/OD 75 (HT pipe) DN/OD 90 (HT pipe) DN/OD 110 (HT pipe) DN/OD 160 (HT pipe) |
| Pipe connection, discharge side | DN 80 |
| Connection venting | DN/OD 75 (HT pipe) |
| Ordering information | |
|---|---|
| Brand | Wilo |
| Product description | DrainLift SANI-M.16T/4C |
| Net weight, approx. m | 40 kg |
| Article number | 2549922 |